Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



10.12. Removal and generator installation

EXCEPT FOR GENERATORS OF A SMALL-SIZED SERIES

Removal

Detachment of wires from plugs on a back part of the DELCO-REMY generator

Detachment of the tire of grounding from the top bolt of fastening of the generator

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. For improvement of access disconnect the main air branch pipe from the air filter, the air chamber or the throttle case.
3. Mark and disconnect electric wires from a back part генерато ра (see fig. A detachment of wires from plugs on a back part of the DELCO-REMY generator).
4. Remove a driving belt of the generator.
5. Unscrew two bolts and nuts and remove washers and plugs, thus remember their arrangement. Note a place of fastening of the tire of grounding (see fig. A detachment of the tire of grounding from the top bolt of fastening of the generator).
6. Remove the generator.

Installation

Installation is made in sequence, return to removal taking into account the next moments...

PERFORMANCE ORDER
1. Fix the tire of grounding by the top bolt of fastening of the generator.
2. Establish and adjust a tension of a driving belt of the generator.

GENERATORS OF A SMALL-SIZED SERIES

Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. For improvement of access remove an air inlet and the air filter.
3. If the driving belt of the generator is repeatedly established, chalk note the direction of its rotation.
4. Using a wrench, turn a roller of the automatic mechanism of a tension clockwise if to look on the right side of the car, and зафикси руйте it in this situation. After reduction of a tension of a driving belt remove it from pulleys and return the tension mechanism to a starting position.
5. Mark and disconnect electric wires from a back part of the generator.
6. Unscrew a bolt of the bottom fastening of the generator. Weaken the top bolts of fastening of an arm of the generator to the engine.
7. Unscrew two bolts, fixing the generator to arms, thus note an arrangement of bolts as they have various length. Remove the generator.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.
2. Installation is made in sequence, return to removal. Tighten bolts of fastening of the generator the demanded moment and establish a driving belt.