Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



10.20. Cover and rotor of the distributor of ignition

Removal

MODELS 14 NV I OF 16 SV

Removal of a cover of the distributor of ignition on model of 1,6 l (BOSCH distributor)

Removal of a cover of the distributor of ignition on model of 1,6 l (LUæAS distributor)

Removal of a rotor of the distributor and the plastic filter on model of 1,6 l (BOSCH distributor)

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Mark and disconnect high-voltage wires from a cover of the distributor of ignition and spark plugs, thus pull not for a wire, and for a candle tip. Also remove the high-voltage wire connecting the coil of ignition to a cover of the distributor of ignition.
3. On the BOSCH distributor, using a screw-driver edge, remove two spring brackets and uncover the ignition distributor. On the LUСAS distributor unscrew two screws and uncover the ignition distributor (see fig. Removal of a cover of the distributor of ignition on model of 1,6 l (BOSCH distributor), Removal of a cover of the distributor of ignition on model of 1,6 l (LUæAS distributor)).
4. Having pulled, remove from a shaft a distributor rotor.
5. On the distributor of ignition of BOSCH for access to distributor elements, having pulled, remove from a distributor shaft the plastic filter (see fig. Removal of a rotor of the distributor and the plastic filter on model of 1,6 l (BOSCH distributor)).

OTHER MODELS

Unscrewing of the screw of fastening of a cover of the distributor of ignition on model of 2,0 l

Removal of the plastic screen from the case of the distributor of ignition on model of 2,0 l

Unscrewing of screws of fastening of a rotor of the distributor of ignition

Removal of a rotor of the distributor of ignition on model of 2,0 l

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Mark and disconnect high-voltage wires from a cover of the distributor of ignition and spark plugs, thus pull not for a wire, and for a candle tip. Also remove the high-voltage wire connecting the coil of ignition to a cover of the distributor of ignition.
3. On the DOHC models except Х20 XEV unscrew two bolts and uncover spark plugs a cover of a head of the block of cylinders.
4. Unscrew three screws and uncover the ignition distributor (see fig. Unscrewing of the screw of fastening of a cover of the distributor of ignition on model of 2,0 l).
5. Take the plastic screen from the case of the distributor of ignition. On perimeter of the plastic screen the sealing ring is established. At removal of the plastic screen do not damage a rotor of the distributor of ignition (see fig. Removal of the plastic screen from the case of the distributor of ignition on model of 2,0 l).
6. Using a six-sided key, unscrew two screws and remove a rotor of the distributor of ignition, thus a metal nave of a rotor should remain in the case of the distributor of ignition (see fig. Unscrewing of screws of fastening of a rotor of the distributor of ignition, Removal of a rotor of the distributor of ignition on model of 2,0 l).
7. Check a condition of a sealing ring on the plastic screen and, if necessary, replace it.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal. It is possible to establish a rotor of the distributor of ignition only in one situation. If necessary turn a metal nave of a rotor so that openings under the screw were combined with openings in a rotor of the distributor and distributive to a shaft. Check correctness of connection of high-voltage wires.