Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   - 10.23. Repair of the distributor of ignition
      10.23.2. Models 16 SV
      10.23.3. DOHC models
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



10.23. Repair of the distributor of ignition

10.23.1. Models 14 NV

GENERAL INFORMATION

Prevention

Before repair of the distributor of ignition specify existence and cost of spare parts. Count that, can be to replace the ignition distributor assembled cheaper, than it to repair.


Dismantling

PERFORMANCE ORDER
1. Remove the ignition distributor.
2. Remove a rotor of the distributor and the plastic screen.
3. Unscrew two screws and remove the top basic plate. As spare parts to the distributor of ignition only the vacuum regulator of a corner of an advancing of ignition is delivered. Also it is not required to make adjustment of the distributor of ignition.
4. If necessary, unscrew two screws and remove a vacuum regulator of a corner of an advancing of ignition, previously having disconnected draft of a regulator from a basic plate. Note an arrangement of screws as they have various length because longer screw fixes one of brackets of fastening of a cover of the distributor of ignition.

Check

PERFORMANCE ORDER
1. Check a vacuum regulator, creating in it depression. Thus draft of a regulator should move inside. After vacuum removal draft should return to a starting position. If draft does not move, as it is required, replace a vacuum regulator of an advancing of ignition.
2. Check a condition of a cover of the distributor of ignition on existence of corrosion of contacts, black paths between contacts, and also integrity and smoothness of moving of coal contact in the cover center. In the presence of defects replace a cover of the distributor of ignition.
3. Check a condition and fastening of metal contact of a rotor of the distributor. If contact scorched or weakened its fastening, replace a distributor rotor. At existence, remove from contact a deposit and corrosion traces, using a small file.
4. Check a condition of a sealing ring in a back part of the distributor of ignition and, if necessary, replace it.

Assembly

PERFORMANCE ORDER
1. Assembly is made in sequence, return dismantling. Check correctness and reliability of fastening of draft of a vacuum regulator to a basic plate.
2. Establish the ignition distributor. Then check and if it is necessary, adjust a corner of an advancing of ignition.