Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



10.26. Electronic modules

HEI MODULE (MODELS 14 NV)

Removal

The module is established on a metal plate on the left side of a motor compartment under the ignition coil.

PERFORMANCE ORDER
1. Remove the ignition coil.
2. Unscrew two screws and remove the module from a metal plate.
3. Before installation of the module apply a thin film heatwire paste on an interfaced surface of a metal plate. At installation of the new module in a set of the module there should be a heat conductor a ny paste.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

MSTS-I MODULE (MODELS 1,6 AND 1,8 L)

Removal

MSTS-i module arrangement on model of 1,6 l

PERFORMANCE ORDER
1. The module is established on a partition of a motor compartment over steering transfer (see fig. A MSTS-i module arrangement on model of 1,6 l).
2. Remove a weight wire from the accumulator.
3. For improvement of access remove the air chamber from the carburetor.
4. Disconnect the electric socket from the module.
5. Unscrew two nuts and remove the module from a partition of a motor compartment.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

MOTRONIC MODULE

Removal

Motronic module removal on model of 2,0 l

Detachment of the electric socket from the Motronic module on model 2,0

PERFORMANCE ORDER
1. The module is located behind the lateral panel of furnish in deepening for feet of the driver.
2. Remove a weight wire from the accumulator.
3. Remove the lateral panel of furnish of deepening for feet of the driver.
4. Unscrew two screws from above and one screw from below, fixing the module and lower the module down (see fig. Motronic module removal on model of 2,0 l).
5. Release fixing bracket and disconnect from the module the electric socket (see fig. A detachment of the electric socket from the Motronic module on model 2,0).
6. Take the module from car salon.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.