Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



10.27. Elements MSTS-i

THE SENSOR OF ABSOLUTE PRESSURE IN THE INLET COLLECTOR

Removal

Arrangement of the sensor of absolute pressure in an inlet collector of MSTS-i on model of 1,6 l

PERFORMANCE ORDER
1. The sensor is established on a partition of a motor compartment to the left of the MSTS-i module under a windscreen fairing (see fig. An arrangement of the sensor of absolute pressure in an inlet collector of MSTS-i on model of 1,6 l).
2. Remove a weight wire from the accumulator.
3. For improvement of access to the sensor raise an edge of a fairing of a windscreen.
4. Disconnect from the sensor the electric socket and a vacuum tube.
5. Having pulled up, remove the sensor of absolute pressure in an inlet collector from an arm.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal. Keep in mind that on models with system of injection of Multec there is no canister with charcoal for catching паров fuels therefore a vacuum hose of the sensor it is necessary to dispose horizontally at distance from the sensor to the throttle case. In this case hit of drops of fuel in the sensor or a hose is excluded.

SENSOR OF TEMPERATURE OF OIL

Removal

Wrench use for unscrewing of the sensor of temperature of MSTS-i oil on model of 1,6 l

PERFORMANCE ORDER
1. The sensor is screwed in in the block of cylinders of the engine from an inlet collector about a starter.
2. Access to the sensor is most convenient from the top part of a motor compartment.
3. Remove a weight wire from the accumulator.
4. Disconnect from the sensor the electric socket.
5. Unscrew the sensor from the block of cylinders and close an opening for the sensor a suitable stopper (see fig. Wrench use for unscrewing of the sensor of temperature of MSTS-i oil on model of 1,6 l).

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.