Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
- 10. Engine electrosystems
   10.2. General information
   10.3. Ignition system
   10.4. Check of system of ignition
   10.5. Rules of care of the accumulator
   10.6. Accumulator check
   10.7. Battery charging
   10.8. Accumulator
   10.9. Charging system
   10.10. Generator
   10.11. Driving belt of the generator
   10.12. Removal and generator installation
   10.13. Generator brushes
   10.14. BOSCH generator
   10.15. Small-sized DELCO-REMY generator
   10.16. System of start of the engine
   10.17. Starter
   10.18. Removal and starter installation
   10.19. Ignition coil
   10.20. Cover and rotor of the distributor of ignition
   10.21. Distributor of ignition (SOHC model)
   10.22. Distributor of ignition (DOHC model)
   + 10.23. Repair of the distributor of ignition
   10.24. Check and adjustment of a corner of an advancing of ignition
   10.25. Fine tuning of the moment of ignition under a used grade of fuel
   10.26. Electronic modules
   10.27. Elements MSTS-i
   10.28. Sensor of speed/provision of a cranked shaft (model of 1,8 l)
   10.29. Motronic system elements
   10.30. Sensor of a detonation (DOHC model)
   10.31. DIS module
   10.32. Sensor of phases of a camshaft (HE C20 engine)
   10.33. System of prestarting heating
   10.34. Glow plugs
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



10.6. Accumulator check

GENERAL INFORMATION

In the accumulator it is necessary to make check of density of electrolit each 3 months to define loading ability of the accumulator.

Check is made by a plotnomer. At determination of density of electrolit it is necessary to consider accumulator temperature. At temperature of electrolit is lower 15°С on everyone 10 ° less than this temperature from the measured density subtract value 0.007. For everyone 10 ° over 15 ° add 0.007.

The electrolit density in the accumulator should be in the following limits:
Temperature
Above 25°С
Below 25°С
Full charging
1,210-1,230
1,270-1,290
Charging for 70 %
1,170-1,190
1,230-1,250
The discharged
1,050-1,070
1,110-1,130

Density of electrolit measure in everyone bank. The difference in density 0,04 or more between two any banks indicates loss of electrolit or a sulfatatsiya of plates.

If the electrolit density between two any banks differs more than on 0,04 accumulator is subject to replacement. If the density of electrolit is lower demanded, but identical in all banks, the accumulator is necessary for charging.

In case of use необслуживае the my accumulator the condition of the accumulator can be checked only the voltmeter. In accumulators with the built-in indicator of degree of a zaryazhennost the condition of the accumulator is determined by color of the indicator. Green color of the indicator corresponds to a full battery charging. Black color of the indicator indicates need of a battery charging. Dark blue color of the indicator testifies to low level of electrolit in the accumulator.