Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
- 11. Transmission
   11.2. General information
   11.3. Coupling cable
   11.4. Adjustment of a cable of coupling
   11.5. Coupling pedal
   + 11.6. Couplings (the engine and a transmission are established in the car)
   11.7. Coupling (the transmission is removed)
   11.8. Vyzhimna bearing
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



11.8. Vyzhimna bearing

GENERAL INFORMATION

Prevention

At installation of the directing plug of the vyzhimny bearing it is necessary to use a new sealing ring.


Removal

Removal of the vyzhimny bearing from the directing plug

Extraction of an axis of the squeezing lever and removal of a fork of switching off of coupling

Installation of a sealing ring of the directing plug

Installation of the directing plug of the vyzhimny bearing

Installation of the plastic plug of an axis of the squeezing lever

PERFORMANCE ORDER
1. For access to the vyzhimny bearing it is necessary to remove coupling.
2. Unscrew a bolt, fixing a fork of switching off of coupling to an axis of the squeezing lever.
3. If the coupling cable is not disconnected from a transmission yet, remove a bracket, fixing a carving tip of a cable of coupling to the squeezing lever, and remove a cable tip from the squeezing lever.
4. Remove vyzhimny the bearing from the directing plug. Take from a coupling case an axis of the squeezing lever, thus an axis also should leave a fork of switching off of coupling (see fig. Removal of the vyzhimny bearing from the directing plug, Extraction of an axis of the squeezing lever and removal of a fork of switching off of coupling). At existence take vyzhimny the bearing from a plastic ring.
5. Believe vyzhimny the bearing which should rotate easily, evenly and silently. The working surface of the bearing influencing a press spring should be smooth, without cracks, local corrosion or development. In the presence of defects vyzhimny it is necessary to replace the bearing.
6. At installation of new coupling vyzhimny it is also necessary to replace the bearing.
7. If necessary unscrew three bolts and remove directing plug of the vyzhimny bearing. After removal of the directing plug of the vyzhimny bearing it is possible to replace a sealing ring of an entrance shaft of a transmission. Remove the sealing ring established between the directing plug and a case of coupling. Using screw-drivers as the lever, take a sealing ring from the directing plug. Using a tubular opravka of the corresponding diameter, establish a new sealing ring in directing plug. Fill space between working edges of a sealing ring lithium greasing, then establish directing plug with a new sealing ring. At installation of a sealing ring of the directing plug do not use greasing (see fig. Installation of a sealing ring of the directing plug, Installation of the directing plug of the vyzhimny bearing).
8. If necessary, replace plastic plugs of an axis of the squeezing lever for what beat out them from a coupling case, using a drift and a hammer. Establish new plugs in a case the couplings thus blocking uvulas of plugs should enter into the corresponding grooves in a coupling case (see fig. Installation of the plastic plug of an axis of the squeezing lever).

Installation

Tightening of a bolt of fastening of a fork of switching off of coupling

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal taking into account the next moments.
2. Apply a thin film greasings on the basis of a molybdenum disulfide on an internal surface of plugs of an axis of the squeezing lever and an external surface of the directing plug of the vyzhimny bearing.
3. At existence establish vyzhimny the bearing in a plastic ring, then establish vyzhimny the bearing together with a fork of switching off of coupling on directing plug. Insert into a coupling case an axis of the squeezing lever and tighten a bolt of fastening of a fork of switching off of coupling (see fig. Tightening of a bolt of fastening of a fork of switching off of coupling).
4. Establish coupling.
5. Check and, if necessary, adjust a coupling cable.