Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
- 12. Mechanical transmission
   12.2. General information
   12.3. Adjustment of draft of the mechanism of a choice of transfers
   12.4. Knot of the lever of gear shifting
   12.5. Draft of the mechanism of a choice of transfers
   12.6. Gear shifting lever
   12.7. Protective cover of the lever of gear shifting
   12.8. Sealing rings of differential
   12.9. Sealing ring of an entrance shaft of a transmission
   12.10. Removal and transmission installation
   12.11. Transmission repair
   12.12. Speedometer drive
   12.13. Switch of lamps of a backing
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



12.3. Adjustment of draft of the mechanism of a choice of transfers

GENERAL INFORMATION

Prevention

After carrying out adjustment close a regulator opening in a cover of the mechanism of a choice of transfers by a new stopper.


Arrangement of the tightening bolt, the mechanism of a choice of transfers fixing a rod to draft

Stopper extraction from an opening for adjustment in a cover of the mechanism of a choice of transfers

Drill installation
At drill installation, it should enter into an opening in the lever of a choice of transfers.

Arrow on the gear shifting lever
The arrow on the lever of gear shifting should be combined with a cut of elements of blocking of inclusion of transfer of a backing.

Gap between a hook and an emphasis
The gap between a hook (And) and an emphasis (In) should make no more than 3 mm.

PERFORMANCE ORDER
1. In a motor compartment weaken tightening a bolt, a fixing rod of the mechanism of a choice of transfers to draft (see fig. An arrangement of the tightening bolt, the mechanism of a choice of transfers fixing a rod to draft). On models since 1993 the arrangement of a tightening bolt and access to it is changed is most convenient from under the car.
2. Take a stopper closing an opening for adjustment in a cover of the mechanism of a choice of transfers (see fig. Stopper extraction from an opening for adjustment in a cover of the mechanism of a choice of transfers).
3. Turn a rod of the mechanism of a choice of transfers counter-clockwise so that the drill in diameter of 4,5 mm, inserted through an opening for adjustment in a cover of the mechanism of a choice of transfers entered into an opening in the lever of a choice of transfers (see fig. Drill installation).
4. In car salon for access to the basis of the lever of gear shifting remove a protective cover of the lever of gear shifting from the central console.
5. The assistant should hold the gear shifting lever in neutral situation in a point of inclusion of the first/second of transfers. Thus the lever should rest against an element of blocking of inclusion of transfer of a backing, and an arrow and a cut should settle down how is shown on fig. An arrow on the gear shifting lever
6. On models since 1993 after installation of the lever of gear shifting in situation for adjustment insert the second drill in diameter of 4,5 mm into an opening in the gear shifting lever. Thus there is a blocking of the lever of gear shifting for the period of adjustment and the help of the assistant is not required. In this position of the lever tighten tightening a bolt, a fixing rod of the mechanism of a choice of transfers to draft.
7. On models till 1993 check that the gap between a hook (And) and an emphasis (In) in the basis of the lever of gear shifting made no more than 3 mm (see fig. A gap between a hook and an emphasis).
8. Establish a protective cover of the lever of gear shifting on the central console.
9. Take a drill from an opening for adjustment in a cover of the mechanism of a choice of transfers and close an opening a new stopper.
10. Check operation of the mechanism of a choice of transfers on single turns of the engine.