Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
- 15. Brake system
   15.2. General information
   15.3. Anti-blocking system of brakes (ABS)
   15.4. Pumping of hydraulic brake system
   + 15.5. Replacement of forward brake shoes
   15.6. Replacement of back brake shoes on disk brakes
   + 15.7. Replacement of back brake shoes on drum-type brakes
   15.8. Replacement of brake shoes of the hand brake on back disk brakes
   15.9. Support of a forward brake
   15.10. Support of a back disk brake
   15.11. Brake disk
   15.12. Forward brake disk
   15.13. A back brake disk on models with SOHC engines
   15.14. A back brake disk on models with DOHC engines
   15.15. Brake drum
   15.16. Back working brake cylinder
   15.17. Brake board of a back brake
   15.18. Protective casing of a forward brake disk
   15.19. Main brake cylinder
   15.20. Repair of the main brake cylinder (model without ABS)
   15.21. Vacuum amplifier of brakes
   15.22. Hydraulic ABS modulator
   15.23. The ABS sensors established on wheels
   15.24. ABS control unit
   15.25. ABS relay (only ABS-2E system)
   15.26. Valves of adjustment of pressure
   15.27. Brake pipelines and hoses
   15.28. Adjustment of the hand brake
   + 15.29. Cable of the hand brake
   15.30. Lever of the hand brake
   15.31. Brake pedal
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



15.24. ABS control unit

ABS-2E SYSTEM

Removal

ABS control unit extraction

Detachment of the electric socket from the control unit on ABS-2E system

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. The control unit is located under a cover in a threshold from the passenger on the right side from a seat.
3. Unscrew three screws and uncover the control unit. Keep in mind that two screws are closed by plastic caps.
4. Take the control unit from an aperture, then release clamps and disconnect from the block the electric socket. Take the control unit from the car (see fig. ABS control unit extraction, the Detachment of the electric socket from the control unit on ABS-2E system).

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.
2. Check that the control lamp of ABS dies away after engine start.

ABS-2EH SYSTEM

Removal

Arrangement of the control unit of ABS-2EH system
1–the block with a high cover;
2–the block with a low cover

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Uncover the hydraulic modulator.
3. Disconnect electric sockets of the electromagnetic block and a plait of wires.
4. Removal of the relay can be made only from control units with high covers (see fig. Arrangement of the control unit of ABS-2EH system). Remove the relay of the electromagnetic block and the pump engine. If the control unit with a low cover is faulty, replace the block together with the relay.
5. Unscrew bolts and remove the control unit.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.