Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.11. Adjustment of the bearing of a back wheel (SOHC model)

GENERAL INFORMATION

Prevention

For fastening of a nut of a nave it is necessary to use new шплинт.


Removal of a dustproof cap from a nave on models with back disk brakes

Check люфта bearings moving by a screw-driver of a persistent washer

PERFORMANCE ORDER
1. At existence remove a wheel cap, then weaken bolts of fastening of a back wheel. Lift a back part of the car and fix on supports. Remove a back wheel.
2. Using a screw-driver edge, remove a dustproof cap from a nave (see fig. Removal of a dustproof cap from a nave on models with back disk brakes).
3. Take шплинт, fixing a nave nut from unscrewing, then weaken a nut of fastening of a nave.
4. Tighten a nut of fastening of a nave the moment of 25 Nanometers, thus turn a nave.
5. Weaken a nut of fastening of a nave until while the persistent washer located under a nut can be moved a screw-driver edge in different directions (see fig. Check люфта bearings moving by a screw-driver of a persistent washer).
6. Establish new шплинт, fixing a nave nut from unscrewing. Thus if the opening under шплинт in a pin is not combined with grooves on a nave nut, tighten a nut before combination of an opening with the next groove. Check that the persistent washer can still move. Otherwise weaken a nut before combination of the next groove on a nut with an opening in a nave pin.
7. Establish a wheel and lower the car. Tighten bolts of fastening of a wheel the demanded moment.