Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)

GENERAL INFORMATION

Prevention

At installation it is necessary to use new nuts of fastening of a fixing element of a nave.


Not folding knot of a nave and the bearing of a back wheel on late models with ABS

1–nave;
2–fixing element of a nave;
3–bolt;
4–a dustproof cap with the ABS sensor;
5–bearing;
6–sealing ring

Removal

PERFORMANCE ORDER
1. Since 1993 on all models устанавли not folding knot of a nave and the bearing of a back wheel (see drawing) is howled.
2. As the knot consisting of a fixing element of a nave, a nave and the bearing of a nave is not folding knot, adjustment of the bearing is not required.
3. Remove a wheel cap, then weaken bolts of fastening of a wheel. Lift a back part of the car and fix on supports. Remove the corresponding back wheel.
4. Remove a support of a back disk brake. Without disconnecting from a support a brake hose, using a soft wire, tie up a support to a back suspension bracket, thus do not stretch and overwind a brake hose.
5. Remove a returnable spring from the lever of a block of the hand brake and a brake board.
6. Unscrew the screw and remove a brake disk.
7. Disconnect the electric socket from the ABS sensor.
8. Unscrew four nuts and remove nave knot together with a brake board. As soon as there will be an access, disconnect a cable of the hand brake from the lever of a block of the hand brake.

Installation

Installation is made in sequence, return to removal taking into account the next moments...

PERFORMANCE ORDER
1. Tighten nuts of fastening of knot of a nave the demanded moment.
2. Check correctness of connection of a cable of the hand brake and a returnable spring.
3. Establish a brake disk and a brake support.
4. Check adjustment of a cable of the hand brake, then establish a wheel and lower the car on the earth.