Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.14. A nave of a back wheel (model with the SOHC engine)

GENERAL INFORMATION

Prevention

At installation it is necessary to use new шплинт, fixing a nave nut from unscrewing.


Nave installation / brake disk

Washer installation on a nave / a brake disk

Nuts of fastening of a nave / brake disk

MODELS WITH BACK DRUM-TYPE BRAKES

Removal

PERFORMANCE ORDER
1. At existence remove a wheel cap, then weaken bolts of fastening of a back wheel. Lift a back part of the car and fix on supports. Remove the corresponding back wheel.
2. Remove a brake drum.
3. Using a screw-driver edge as the lever, remove a dustproof cap of a nave.
4. Take шплинт, fixing a nave nut from unscrewing, then unscrew a nut of fastening of a nave. For nave deduction from a provorachivaniye when unscrewing a nut of fastening of a nave screw in in a nave two bolts of fastening and insert between bolts mount.
5. Remove from a nave pin a persistent washer and a nave.

Installation

PERFORMANCE ORDER
1. Establish a nave and an internal ring of the external bearing on a nave pin. Thus do not damage the sealing ring established from the interior of a nave.
2. Establish a persistent washer and screw a nut of fastening of a nave, then adjust люфт the bearing of a back wheel.
3. Using new шплинт, fix a nut of fastening of a nave from unscrewing, then establish a dustproof cap of a nave.
4. Establish a brake drum and check adjustment of a cable of the hand brake.
5. Lower the car on the earth and tighten bolts of fastening of a wheel the demanded moment.

MODELS WITH BACK DISK BRAKES

Removal

PERFORMANCE ORDER
1. On models with back disk brakes the nave and a brake disk represent one detail.
2. At existence remove a wheel cap, then weaken bolts of fastening of a back wheel. Lift a back part of the car and fix on supports. Remove the corresponding back wheel.
3. Remove a brake support, without disconnecting from it a brake hose and using a soft wire, suspend a support to a back suspension bracket.
4. Using a screw-driver edge as the lever, remove a dustproof cap of a nave.
5. Take шплинт, fixing a nave nut from unscrewing, then unscrew a nut of fastening of a nave. For nave deduction from a provorachivaniye when unscrewing a nut of fastening of a nave screw in in a nave two bolts of fastening and insert between bolts mount.
6. Unscrew a nut and remove from a nave pin a washer and a nave / a brake disk. If a nave / a brake disk do not act in film, take away from a brake drum of a block of the hand brake for what insert a screw-driver through an adjusting opening in a nave / a brake disk and turn a regulator wheel.

Installation

PERFORMANCE ORDER
1. Establish a nave / a brake disk and an internal ring of the external bearing on a nave pin. Thus do not damage the sealing ring established from the interior of a nave / a brake disk.
2. Establish a persistent washer and screw a nut of fastening of a nave, then adjust люфт the bearing of a back wheel.
3. Using new шплинт, fix a nut of fastening of a nave from unscrewing, then establish a dustproof cap of a nave.
4. Check adjustment of the hand brake and establish a brake support.
5. Lower the car on the earth and tighten bolts of fastening of a wheel.