Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.24. Replacement of the bearing of a back wheel (model with DOHC engines)

GENERAL INFORMATION

Prevention

As bearing replacement rather difficult operation, before its performance read all section. For performance of this operation it is necessary to use a dinamometrichesky key and a special stripper, and also a new nut of fastening of a nave.


Removal

Arrangement of a plastic cover on a gear rotor of the ABS sensor

Arrangement of a nut of fastening of a nave of a back wheel on models with DOHC engines

Removal of a lock ring of the bearing of a nave on models with DOHC engines

PERFORMANCE ORDER
1. Lift a back part of the car and fix on supports. Remove back wheels.
2. Remove a bracket of fastening and take a brake tube from an arm on a number diagonal the lever. Keep in mind that on a bracket the ABS sensor wire is also fixed.
3. Unscrew bolts and remove a support of a brake and an ABS sensor arm from a brake board. Using a soft wire, tie up a support with an ABS sensor arm to the car bottom.
4. Unscrew the screw and remove a brake disk. If the brake disk does not act in film, take away from it blocks of the hand brake, rotating a regulator a screw-driver inserted through an opening in a brake disk.
5. Using the face key inserted through an opening in a flange of a nave, unscrew four bolts, fixing a brake board. Keep in mind that the top bolts are shorter than the bottom.
6. Using a screw-driver edge as the lever, remove a plastic cover from a back part of a gear rotor of the ABS sensor for access to a nut of fastening of a nave (see fig. An arrangement of a plastic cover on a gear rotor of the ABS sensor, the Arrangement of a nut of fastening of a nave of a back wheel on models with DOHC engines).
7. Using a screw-driver edge as the lever, unbend blocking rim of a nut of a nave and remove it from a gear rotor of the ABS sensor.
8. When unscrewing a nut of fastening of a nave for nave deduction from a provorachivaniye screw in two bolts of fastening of a wheel in a flange of a nave and insert between them mount. Unscrew a nut of fastening of a nave.
9. Using a stripper, remove from a nave a gear rotor of the ABS sensor.
10. Using a stripper established on the diagonal lever, remove a nave of a back wheel from the bearing. Keep in mind that the internal ring of the bearing can remain on a nave.
11. Remove a lock ring of the bearing from the outer side of the diagonal lever (see fig. Removal of a lock ring of the bearing of a nave on models with DOHC engines). Beat out a copper drift an external ring of the bearing from a nave, thus a drift устанавли howl evenly around in order to avoid a bearing distortion.
Prevention

At knocking-out of the bearing be careful, that did not remain забоины on a bearing seat in a nave.


12. If the internal ring of the bearing remained on a nave, remove it with stripper application.

Installation

PERFORMANCE ORDER
1. Clear all details and check their condition.
2. Using a tubular opravka of the corresponding diameter, pressing an external ring of the bearing, establish the new bearing in the diagonal lever. Establish the bearing against the stop it in a fillet.
3. Establish a lock ring of the bearing and check that it is accurate зафиксиро валось in a flute.
4. While the assistant supports an internal ring of the bearing, from a reverse side of the diagonal lever with use of a metal tubular opravka from outer side of the diagonal lever insert a nave into place. Do not apply sharp and big efforts as the bearing is easy for damaging.
5. Establish on a nave a gear rotor of the ABS sensor. Thus from the outer side support a nave.
6. Screw a new nut of fastening of a nave and tighten it the demanded moment. Thus hold a nave from a provorachivaniye also, as well as at removal.
7. Establish on a nave nut a new blocking rim and unbend it to a gear rotor of the ABS sensor.
8. Establish a plastic cover on a back part of a gear rotor of the ABS sensor.
9. Screw in bolts of fastening of a brake board and fix them the demanded moment.
10. Establish a brake disk and fix it the screw, then several times tighten the hand brake in order that the mechanism of a regulator moved blocks into position.
11. Establish on a brake board a support and an arm of the ABS sensor and tighten bolts of fastening the demanded moment.
12. Establish a brake tube in an arm on the diagonal lever and fix it a bracket.
13. Establish a wheel, then lower the car on the earth and tighten bolts of fastening of a wheel the demanded moment.