Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.3. Replacement of the bearing of a forward wheel

Removal

Expression of a nave of a forward wheel from the bearing

Removal internal a bearing ring from a nave

Unscrewing of the screw of fastening of a protective board of a brake disk

Removal of the lock ring, the bearing fixing an external ring

PERFORMANCE ORDER
1. Remove a rack of a forward suspension bracket together with a rotary fist.
2. Unscrew the screw and remove from a nave a brake disk.
3. For nave extraction from a rotary fist use a press and a tubular opravka of the corresponding diameter. Establish a rotary fist on steel cores inside up and, using a metal opravka, squeeze out a nave from nave bearings (see fig. Expression of a nave of a forward wheel from the bearing).
4. Using a stripper, remove an internal ring of the bearing from a nave (see fig. Removal internal a bearing ring from a nave).
5. Unscrew three screws and remove a protective board of a brake disk from a rotary fist (see fig. Unscrewing of the screw of fastening of a protective board of a brake disk).
6. Remove from a rotary fist the lock rings, fixing an external ring of the bearing (see fig. Removal of the lock ring, the bearing fixing an external ring).
7. Opiry an internal part of a rotary fist on supports and using a tubular opravka of the corresponding diameter, squeeze out an external ring of the bearing from a rotary fist.

Installation

Arrangement of the bearing of a nave of a forward wheel
And – an external lock ring of the bearing;
In – an internal lock ring of the bearing

Installation of the bearing of a nave of a forward wheel with использова niy a tubular opravka, a nut, a bolt and washers of the corresponding diameter

Installation of a nave of a forward wheel with use of a tubular opravka, a nut, a bolt and washers of the corresponding diameter

PERFORMANCE ORDER
1. Clear a nave and a rotary fist of dirt, and greasings. Establish an external lock ring of fastening of the bearing (see fig. Arrangement of the bearing of a nave of a forward wheel). Keep in mind that uvulas of a lock ring should be turned to the basis of a rotary fist.
2. Reliably fix a rotary fist on supports and establish on it the bearing. Installation of the bearing make with use of a tubular opravka which should press on an external ring of the bearing. The bearing establish against the stop it in an external lock ring (see fig. Installation of the bearing of a nave of a forward wheel with использова niy a tubular opravka, a nut, a bolt and washers of the corresponding diameter).
3. Establish an internal lock ring of the bearing that uvulas of a lock ring were turned to the basis of a rotary fist.
4. Establish a protective board of a brake disk.
5. Establish a nave in the bearing. Thus use a tubular opravka which presses on an internal ring of the bearing. The nave press fitting in the bearing can be made with use of a long bolt, a nut and washers of the corresponding diameter (see fig. Installation of a nave of a forward wheel with use of a tubular opravka, a nut, a bolt and washers of the corresponding diameter).
6. Establish a brake disk.
7. Establish a rack of a forward suspension bracket with a rotary fist on the car.