Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.40. Tips of steering draft

GENERAL INFORMATION

Prevention

At removal of a tip of steering draft it is necessary to use a stripper of spherical hinges. At installation it is necessary to use new самоконтрящуюся a nut of fastening of the spherical hinge of a tip of steering draft.


Removal

The bottom view on a tip of steering draft
1–tightening bolt of a tip of steering draft;
2–carving regulator of steering draft;
3–tightening bolt of steering draft

Removal of the spherical hinge of a tip of steering draft from a rack of a forward suspension bracket

PERFORMANCE ORDER
1. At existence remove a wheel cap, then weaken bolts of fastening of a forward wheel. Tighten the hand brake, then lift a forward part of the car and fix on supports. Remove the corresponding forward wheel.
2. Weaken a bolt clamping a tip of steering bent for to a carving regulator of steering draft (see fig. The bottom view on a tip of steering draft).
3. Unscrew самоконтрящуюся a nut, fixing the spherical hinge of a tip of steering bent for to a rack of a forward suspension bracket.
4. Using a stripper of spherical hinges, take a pin of the spherical hinge of a tip of steering draft from a rack of a forward suspension bracket (see fig. Removal of the spherical hinge of a tip of steering draft from a rack of a forward suspension bracket).
5. Using paint or a sticky tape, note an arrangement of a tip of steering draft on a carving regulator. It is also possible to count number of rounds of a carving on an acting part of a carving regulator. Unscrew a tip from steering draft.
6. The tip right the helmsman of draft is marked by a letter R, and a tip left the helmsman of draft has no marking.

Installation

PERFORMANCE ORDER
1. Screw a tip of steering draft on a carving regulator in the same situation, as before removal.
2. Establish a pin of the spherical hinge of a tip of steering draft on a rack of a forward suspension bracket and fix new самоконтрящейся a nut, having tightened it the demanded moment.
3. Tighten a bolt clamping a tip of steering draft.
4. Establish a wheel and lower the car on the earth. Tighten bolts of fastening of a wheel the demanded moment.
5. Check and, if necessary, adjust corners of installation of forward wheels.