Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.41. Steering draft

GENERAL INFORMATION

Prevention

At installation it is necessary to use the new fixing plate established on heads of bolts of fastening of steering bent for to steering transfer. At removal of steering draft together with a steering tip it is necessary to use a stripper of spherical hinges and new самоконтрящуюся a nut, fixing the spherical hinge to a rack of a forward suspension bracket.


Removal

Fastening of steering bent for to steering transfer
1–bolts;
2–a fixing plate;
3–plate

PERFORMANCE ORDER
1. At existence remove a wheel cap, then weaken bolts of fastening of a forward wheel. Tighten the hand brake, then lift a forward part of the car and fix on supports. Remove the corresponding forward wheel.
2. Unscrew самоконтрящуюся a nut, fixing the spherical hinge of a tip of steering bent for to a rack of a forward suspension bracket.
3. Using a stripper of spherical hinges, take a pin of the spherical hinge of a tip of steering draft from a rack of a forward suspension bracket.
4. If steering draft acts in film without a tip, weaken tightening a bolt, fixing steering bent for to a carving regulator on a tip.
5. Using a screw-driver edge as the lever, remove fixing plate from heads of the bolts, fixing steering bent for to steering transfer and unscrew bolts (see drawing).
6. If steering draft acts in film assembled together with steering tips, take it from under the car.
7. If steering draft acts in film without a steering tip, note paint or a sticky tape note the provision of a tip on a carving regulator, or count number of rounds of a carving on an acting part of a carving regulator. Unscrew steering draft from a tip and take from under the car.

Installation

Installation is made in sequence, return to removal taking into account the next moments...

PERFORMANCE ORDER
1. On bolts of fastening of steering bent for it is necessary for steering transfer to establish a new fixing plate.
2. If steering draft is established together with a steering tip, connect a pin of the spherical hinge of a steering tip from a resistant forward suspension bracket and fix new самоконтрящейся a nut, having tightened it the demanded moment.

3. If steering draft is established without a steering tip, screw draft in a carving regulator in the same situation, as before removal and tighten tightening a bolt.
4. Lower the car on wheels and tighten bolts of fastening of a wheel.
5. Check and, if necessary, adjust corners of installation of forward wheels.