Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
- 16. Suspension bracket
   16.2. General information
   16.3. Replacement of the bearing of a forward wheel
   16.4. Forward bottom frame
   16.5. Rack of a forward suspension bracket
   16.6. Bottom lever of a forward suspension bracket
   16.7. Replacement of plugs of the bottom lever of a forward suspension bracket
   16.8. Spherical hinge of the bottom lever of a forward suspension bracket
   16.9. Forward stabilizer of cross-section stability
   16.10. Replacement of plugs of the forward stabilizer cross-section устойчи vost
   16.11. Adjustment of the bearing of a back wheel (SOHC model)
   16.12. Replacement of the bearing of a back wheel (the SOHC model till 1993)
   16.13. Replacement of the bearing of a nave of a back wheel (model since 1993)
   16.14. A nave of a back wheel (model with the SOHC engine)
   16.15. Back shock-absorber
   16.16. Replacement of rubber elements of fastening of the back shock-absorber
   16.17. Springs of a back suspension bracket (SOHC model)
   16.18. Knot of longitudinal levers of a back suspension bracket (model with SOHC engines)
   16.19. Back stabilizer of cross-section stability
   16.20. Replacement of the plug of the longitudinal lever of a back suspension bracket
   16.21. A fixing element of a back nave (model with SOHC engines)
   16.22. Check of system of a being self-leveled back suspension bracket
   16.23. Control system elements being self-leveled a back suspension bracket
   16.24. Replacement of the bearing of a back wheel (model with DOHC engines)
   16.25. A nave of a back wheel (model with DOHC engines)
   16.26. Knot of a back suspension bracket (model with DOHC engines)
   16.27. The diagonal lever of a back suspension bracket (model with DOHC engines)
   16.28. Back stabilizer of cross-section stability
   16.29. Steering wheel
   16.30. Centering of a steering wheel
   16.31. Replacement of the elastic coupling of a shaft of steering transfer
   16.32. Steering column
   16.33. Repair of a steering column
   16.34. Shock-absorber of steering transfer
   + 16.35. Replacement of protective casings of steering transfer
   16.36. Air removal from steering system with the amplifier
   16.37. Pump of the amplifier of a steering
   16.38. Popolnitelny tank of system of the amplifier of a steering
   16.39. Pipes of cooling of liquid of the amplifier of a steering
   16.40. Tips of steering draft
   16.41. Steering draft
   16.42. Corners of installation of forward wheels
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



16.9. Forward stabilizer of cross-section stability

GENERAL INFORMATION

Prevention

At installation it is necessary to use the new nuts, fixing the stabilizer of cross-section stability to the bottom lever of a forward suspension bracket.


Removal

PERFORMANCE ORDER
1. Using the special adaptation, support the engine and lift a forward part of the car.
2. Remove a reception exhaust pipe.
3. Working under the car, unscrew the nuts, the fixing ends of the stabilizer of cross-section stability to the bottom levers. Remove tarelchaty washers and rubber pillows.
4. Check reliability of support of the engine, then unscrew two nuts, support of the power unit fixing back fastening to the bottom forward frame.
5. A jack through wooden whetstone support the bottom forward frame.
6. Unscrew two back and two central bolts which fix the bottom frame to the car bottom. Keep in mind that back bolts also fix the bottom levers to the bottom frame.
7. Weaken, but do not unscrew completely two bolts, fixing the bottom frame to the car bottom.
8. Being careful, lower the bottom frame and unscrew bolts of fastening of the stabilizer. Then unscrew the forward bolts, fixing the bottom frame to the car bottom.
9. Separate the stabilizer of cross-section stability from the bottom forward frame and the bottom levers and take it from under the car.

Installation

Arrangement of a quencher of fluctuations on the forward stabilizer of cross-section stability

The adjusting sizes of a quencher of fluctuations on the stabilizer of cross-section stability (all sizes in millimeters)

PERFORMANCE ORDER
1. On some models in the center of the stabilizer of cross-section stability the quencher of fluctuations (see fig. is established. An arrangement of a quencher of fluctuations on the forward stabilizer of cross-section stability, the Adjusting sizes of a quencher of fluctuations on the stabilizer of cross-section stability). If the new stabilizer of cross-section stability is established, remove a quencher of fluctuations from the old stabilizer and establish on the new.
2. If necessary replace adjusting plugs of the stabilizer of cross-section stability.
3. Further installation is made in sequence, return to removal taking into account the next moments.
4. Connect the ends of the stabilizer of cross-section stability to the bottom levers, thus the tarelchaty washers, fixing rubber pillows, should be directed by the concave party to the bottom lever.
5. Establish a pin of the spherical hinge of the bottom lever in a rotary fist and fix a nut, having tightened it the demanded moment. Using new шплинт, fix a nut from unscrewing.
6. Tighten all nuts and bolts the demanded moment, thus back bolts of fastening of the bottom forward frame to the bottom of the car should be tightened in some stages.
7. Establish a reception exhaust pipe.
8. Lower the car on wheels and tighten bolts of fastening of wheels the demanded moment.