Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
- 17. Body
   17.2. General information
   17.3. Security measures at carrying out welding works
   17.4. Care of a body
   17.5. Repair of insignificant damages of a body
   17.6. Repair of strong damages of a body
   17.7. Cowl
   17.8. Cowl lock
   17.9. Cable of the lock of a cowl
   17.10. Trunk lid (Sedan models)
   17.11. Lock of a trunk lid (Sedan model)
   17.12. Cylinder of the lock of a trunk lid (Sedan model)
   17.13. Back door (Hatchback models)
   17.14. Lock of a back door (Hatchback model)
   17.15. Cylinder of the lock of a back door (Hatchback model)
   17.16. Racks of a back door (Hatchback model)
   17.17. Doors
   17.18. Door upholstery
   17.19. Internal handle of opening of a door
   17.20. External handle of opening of a door
   17.21. Cylinder of the lock of a door
   17.22. Door lock
   17.23. Limiter of opening of a door
   17.24. Wind and back flew down
   17.25. Back triangular window leaves
   17.26. Door glass
   17.27. Window regulators
   17.28. External rear-view mirror
   17.29. Bumpers
   17.30. Front grille
   17.31. Windscreen deflector
   17.32. Loose leaves of an arch of a wheel
   17.33. Bottom protective plate (mudguard) of the engine
   17.34. Folding shutter of a toplivozalivny mouth of a fuel tank
   + 17.35. Hatch elements
   17.36. Interior furnish
   + 17.37. Panels of furnish of the dashboard
   17.38. Central console
   17.39. Ceiling
   17.40. Sitting (without mechanisms of a tension of seat belts)
   17.41. Seat belts
   17.42. Mechanism of a tension of a seat belt
   17.43. Forward sitting with the mechanism of a tension of a seat belt
+ 18. Electric equipment
+ 19. Check of malfunctions



17.18. Door upholstery

FORWARD DOOR

Removal

Removal of a bracket of fastening of the handle of a window regulator

Removal of decorative furnish of the internal handle of opening of a door

Arrangement of the electric socket of a drive of a rear-view mirror in an arm on the top part of a door

PERFORMANCE ORDER
1. Using a screw-driver edge as the lever, remove a decorative overlay of the button of blocking of the door lock, then remove the blocking button from draft of the lock.
2. On models with manual стеклоподъемни a lump completely close a window and note an arrangement of the handle of a window regulator. Release a bracket of fastening and remove the handle. The bracket is released if to insert a pure fabric between the handle and an upholstery of a door and, stretching a fabric opposite to the bracket ends, hook on a bracket and release it. Thus it is necessary to pull the handle on itself that she after release of a bracket acted in film with шлицов a window regulator (see fig. Removal of a bracket of fastening of the handle of a window regulator).
3. Using a screw-driver edge as the lever, remove plastic decorative furnish of the internal handle of opening of a door (see fig. Removal of decorative furnish of the internal handle of opening of a door).
4. Unscrew seven screws at the basis of an upholstery of a door and at the basis of the handle of opening of a door/armrest. Take a bracket, fixing a pocket of a door which arranges on in the lower back part of a pocket.
5. Using a screw-driver with a wide edge, separate a door upholstery from a door.
6. Unbend an upholstery of a door and take a big bracket in a back part of a door.
7. On models with an electric drive of external rear-view mirrors on a door of the driver disconnect the electric socket from the mirror switch. Remove a weight wire from the accumulator, note a socket arrangement in an arm in the top part of a door and disconnect the electric socket (see fig. An arrangement of the electric socket of a drive of a rear-view mirror in an arm on the top part of a door).
8. On models with marker lights on a door remove a bulb and disconnect the electric socket.
9. Remove from an internal part of a door a loudspeaker and a back fixing bracket of an upholstery of a door which is attached to a door by one screw. Being careful, remove a protective film from a door.
10. If necessary remove from a door upholstery a pocket for what unscrew three screws and release a bracket from a back part of an upholstery of a door.

Installation

Installation is made in sequence, return to removal taking into account the next moments...

PERFORMANCE ORDER
1. If at removal the protective film of a door was damaged, replace it as, otherwise, rain water can get into the car or damage a door upholstery.
2. Check reliability of connection and correctness of an arrangement электричес whom the socket of the switch of provision of a mirror.
3. If at removal of an upholstery of a door fixing brackets were broken, replace them.

BACK DOOR

Removal

Removal of an upholstery of a back door

PERFORMANCE ORDER
1. Using a screw-driver edge as the lever, remove a decorative overlay of the button of blocking of the door lock, then remove the blocking button from draft of the lock.
2. On models with manual стеклоподъемни a lump completely close a window and note an arrangement of the handle of a window regulator. Release a bracket of fastening and remove the handle. The bracket is released if to insert a pure fabric between the handle and an upholstery of a door and, stretching a fabric opposite to the bracket ends, hook on a bracket and release it. Thus it is necessary to pull the handle on itself that she after release of a bracket acted in film with шлицов a window regulator.
3. Using a screw-driver edge as the lever, remove plastic decorative furnish of the internal handle of opening of a door.
4. On models with electric window regulators remove a weight wire from the accumulator, then, being careful, take the switch from an upholstery of a door and disconnect from it the electric socket.
5. Unscrew three screws, doors fixing an upholstery. Two screws are located under furnish of the internal handle of opening of a door, and the third – an arm of a support of the engine;
5–in the basis of the additional handle of a door.
6. Using a screw-driver with a wide edge, separate a door upholstery from a door.
7. Remove a door upholstery (see fig. Removal of an upholstery of a back door).
8. Remove from a door a protective film.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal taking into account the next moments.
2. If at removal the protective film of a door was damaged, replace it as, otherwise, rain water can get into the car or damage a door upholstery.
3. Arrange electroconducting of the switch of a window regulator so that it did not stir work стеклоподъ an emnik.
4. If at removal of an upholstery of a door fixing brackets were broken, replace them.