Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
- 17. Body
   17.2. General information
   17.3. Security measures at carrying out welding works
   17.4. Care of a body
   17.5. Repair of insignificant damages of a body
   17.6. Repair of strong damages of a body
   17.7. Cowl
   17.8. Cowl lock
   17.9. Cable of the lock of a cowl
   17.10. Trunk lid (Sedan models)
   17.11. Lock of a trunk lid (Sedan model)
   17.12. Cylinder of the lock of a trunk lid (Sedan model)
   17.13. Back door (Hatchback models)
   17.14. Lock of a back door (Hatchback model)
   17.15. Cylinder of the lock of a back door (Hatchback model)
   17.16. Racks of a back door (Hatchback model)
   17.17. Doors
   17.18. Door upholstery
   17.19. Internal handle of opening of a door
   17.20. External handle of opening of a door
   17.21. Cylinder of the lock of a door
   17.22. Door lock
   17.23. Limiter of opening of a door
   17.24. Wind and back flew down
   17.25. Back triangular window leaves
   17.26. Door glass
   17.27. Window regulators
   17.28. External rear-view mirror
   17.29. Bumpers
   17.30. Front grille
   17.31. Windscreen deflector
   17.32. Loose leaves of an arch of a wheel
   17.33. Bottom protective plate (mudguard) of the engine
   17.34. Folding shutter of a toplivozalivny mouth of a fuel tank
   + 17.35. Hatch elements
   17.36. Interior furnish
   + 17.37. Panels of furnish of the dashboard
   17.38. Central console
   17.39. Ceiling
   17.40. Sitting (without mechanisms of a tension of seat belts)
   17.41. Seat belts
   17.42. Mechanism of a tension of a seat belt
   17.43. Forward sitting with the mechanism of a tension of a seat belt
+ 18. Electric equipment
+ 19. Check of malfunctions



17.26. Door glass

GENERAL INFORMATION

Unscrewing of the screw of fastening back directing glasses

Unscrewing of the second screw of fastening back directing glasses

Removal back directing glasses from a door

FORWARD DOOR

Removal

Arrangement of the plastic limiter top directing glasses

Arrangement of screws of fastening of the lower part directing to a door

PERFORMANCE ORDER
1. Lower glass of a door down to an emphasis, then remove an upholstery of a door and a protective film.
2. Unscrew a bolt, fixing back directing glasses and take it through an aperture at doors.
3. Remove from the internal and outer side the bottom consolidation of glass.
4. Remove the plastic limiter with top directing glasses (see fig. An arrangement of the plastic limiter top directing glasses).
5. Unscrew two screws, fixing the lower part directing to a door and lower directing (see fig. An arrangement of screws of fastening of the lower part directing to a door).
Incline door glass forward and take it through a window aperture.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal. If necessary adjust a corner I direct Russian cabbage soup after weakening of two screws of fastening. Establish a door upholstery.
2. On models with electric window regulators program the control unit as follows.
3. Close all doors and include ignition.
4. Close each glass, using the corresponding switch and after when glass will be lifted up against the stop, hold the switch of the pressed 5 more seconds.

BACK DOOR

Removal

Removal of internal consolidation from the lower part of an aperture of a window

Glass removal from a back door

PERFORMANCE ORDER
1. Lower glass of a door down to an emphasis, then remove an upholstery of a door and a protective film.
2. Remove consolidation back directing glasses, then unscrew the opened screw, fixing back directing glasses.
3. Unscrew the second screw of fastening back directing glasses access to which is possible from the interior of a door, then remove directing glasses from a door.
4. Remove internal and external consolidations from the lower part of an aperture of a window (see fig. Removal of internal consolidation from the lower part of an aperture of a window).
5. Incline glass forward and take it up from a window aperture (see fig. Glass removal from a back door).

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal. Establish an internal upholstery of a door.
2. On models with electric window regulators program the control unit as follows.
3. Close all doors and include ignition.
4. Close each glass, using the corresponding switch and after when glass will be lifted up against the stop, hold the switch of the pressed 5 more seconds.