Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
- 17. Body
   17.2. General information
   17.3. Security measures at carrying out welding works
   17.4. Care of a body
   17.5. Repair of insignificant damages of a body
   17.6. Repair of strong damages of a body
   17.7. Cowl
   17.8. Cowl lock
   17.9. Cable of the lock of a cowl
   17.10. Trunk lid (Sedan models)
   17.11. Lock of a trunk lid (Sedan model)
   17.12. Cylinder of the lock of a trunk lid (Sedan model)
   17.13. Back door (Hatchback models)
   17.14. Lock of a back door (Hatchback model)
   17.15. Cylinder of the lock of a back door (Hatchback model)
   17.16. Racks of a back door (Hatchback model)
   17.17. Doors
   17.18. Door upholstery
   17.19. Internal handle of opening of a door
   17.20. External handle of opening of a door
   17.21. Cylinder of the lock of a door
   17.22. Door lock
   17.23. Limiter of opening of a door
   17.24. Wind and back flew down
   17.25. Back triangular window leaves
   17.26. Door glass
   17.27. Window regulators
   17.28. External rear-view mirror
   17.29. Bumpers
   17.30. Front grille
   17.31. Windscreen deflector
   17.32. Loose leaves of an arch of a wheel
   17.33. Bottom protective plate (mudguard) of the engine
   17.34. Folding shutter of a toplivozalivny mouth of a fuel tank
   + 17.35. Hatch elements
   17.36. Interior furnish
   + 17.37. Panels of furnish of the dashboard
   17.38. Central console
   17.39. Ceiling
   17.40. Sitting (without mechanisms of a tension of seat belts)
   17.41. Seat belts
   17.42. Mechanism of a tension of a seat belt
   17.43. Forward sitting with the mechanism of a tension of a seat belt
+ 18. Electric equipment
+ 19. Check of malfunctions



17.27. Window regulators

FORWARD DOOR

Removal

PERFORMANCE ORDER
1. Half lower glass, then remove an upholstery of a door and a protective film.
2. Fix glass in half open situation, having established under it a wooden emphasis.
3. Using a drill in diameter of 8,5 mm drill the rivets fixing стеклоподъ an emnik to a door.
4. Remove the plastic limiter with top directing glasses.
5. Unscrew two screws, fixing bottom directing to a door and lower the directing.
On models with electric стеклоподъ emnik remove a weight wire from the accumulator, then disconnect the electric socket from a window regulator drive.
Being careful, take a window regulator through the bottom aperture at doors.

Installation

Window regulator of a forward door

1–arrangement of rivets of fastening of a window regulator;
2–arrangement of the bottom screws of fastening of the directing;
3–top directing and the limiter

Installation is made in sequence, return to removal taking into account the next moments...

PERFORMANCE ORDER
1. Before window regulator fastening to a door check that holders of a window regulator are correctly established in directing (see drawing).
2. Using new rivets, fix a window regulator on a door.
3. Adjust a corner of the bottom I direct glass Russian cabbage soup after weakening of two screws.
4. Establish an internal upholstery of a door.
5. On models with electric window regulators program the control unit as follows.
6. Close all doors and include ignition.
7. Close each glass, using the corresponding switch and after when glass will be lifted up against the stop, hold the switch of the pressed 5 more seconds.

BACK DOOR

Removal

PERFORMANCE ORDER
1. Half lower glass, then remove an upholstery of a door and a protective film.
2. Fix glass in half open situation, having established under it a wooden emphasis.
3. Using a drill in diameter of 8,5 mm drill the rivets fixing стеклоподъ an emnik to a door.
4. On models with electric window regulators remove a weight wire from the accumulator, then disconnect the electric socket from a drive стеклоподъ an emnik.
5. Being careful, take a window regulator through the bottom aperture at doors.

Installation

Installation is made in sequence, return to removal taking into account the next moments...

PERFORMANCE ORDER
1. Before window regulator fastening to a door check correctness of placement of the lever of a window regulator in the directing.
2. Using new rivets, attach a window regulator to a door.
3. Check work of a window regulator and establish an internal upholstery of a door.
4. On models with electric window regulators program the control unit as follows.
5. Close all doors and include ignition.
6. Close each glass, using the corresponding switch and after when glass will be lifted up against the stop, hold the switch of the pressed 5 more seconds.