Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
- 17. Body
   17.2. General information
   17.3. Security measures at carrying out welding works
   17.4. Care of a body
   17.5. Repair of insignificant damages of a body
   17.6. Repair of strong damages of a body
   17.7. Cowl
   17.8. Cowl lock
   17.9. Cable of the lock of a cowl
   17.10. Trunk lid (Sedan models)
   17.11. Lock of a trunk lid (Sedan model)
   17.12. Cylinder of the lock of a trunk lid (Sedan model)
   17.13. Back door (Hatchback models)
   17.14. Lock of a back door (Hatchback model)
   17.15. Cylinder of the lock of a back door (Hatchback model)
   17.16. Racks of a back door (Hatchback model)
   17.17. Doors
   17.18. Door upholstery
   17.19. Internal handle of opening of a door
   17.20. External handle of opening of a door
   17.21. Cylinder of the lock of a door
   17.22. Door lock
   17.23. Limiter of opening of a door
   17.24. Wind and back flew down
   17.25. Back triangular window leaves
   17.26. Door glass
   17.27. Window regulators
   17.28. External rear-view mirror
   17.29. Bumpers
   17.30. Front grille
   17.31. Windscreen deflector
   17.32. Loose leaves of an arch of a wheel
   17.33. Bottom protective plate (mudguard) of the engine
   17.34. Folding shutter of a toplivozalivny mouth of a fuel tank
   + 17.35. Hatch elements
   17.36. Interior furnish
   + 17.37. Panels of furnish of the dashboard
   17.38. Central console
   17.39. Ceiling
   17.40. Sitting (without mechanisms of a tension of seat belts)
   17.41. Seat belts
   17.42. Mechanism of a tension of a seat belt
   17.43. Forward sitting with the mechanism of a tension of a seat belt
+ 18. Electric equipment
+ 19. Check of malfunctions



17.29. Bumpers

FRONT BUMPER

Removal

Unscrewing of the right bolt of fastening of a front bumper (the air filter is removed)

Arrangement of brackets of fastening of a front bumper

PERFORMANCE ORDER
1. Remove headlights.
2. The front bumper acts in film assembled with the forward decorative panel therefore on models with lobbies противотуманны ми headlights disconnect electric sockets from fog lights. On models with DOHC engines and on models since 1993 remove a front grille. At existence also remove a water reflector.
3. The front bumper fastens bolts from two parties and brackets. The right bolt of fastening can be unscrewed assembled with the air filter. If necessary remove the air filter for access to the right bolt of fastening of a bumper.
4. Unscrew the right and left bolts of fastening of a bumper from body panels behind apertures of headlights (see fig. Unscrewing of the right bolt of fastening of a front bumper).
5. Take brackets of fastening of a bumper from a body, moving a bumper forward and remove the bumper ends from wings (see fig. Arrangement of brackets of fastening of a front bumper).
Being careful, remove a bumper from the car.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

REAR BUMPER

Removal

Removal of the back panel of furnish of a luggage carrier

Arrangement of a nut of fastening of a rear bumper

PERFORMANCE ORDER
1. For access to nuts of fastening of a bumper remove the back panel of furnish of a luggage compartment for what a screw-driver take percussion caps, then lift the panel up for release it from the bottom fastenings (see fig. Removal of the back panel of furnish of a luggage carrier, Arrangement of a nut of fastening of a rear bumper).
2. The bumper acts in film assembled with the bottom decorative panel of furnish.
3. Remove a weight wire from the accumulator, then remove a lamp of illumination of registration plate from a bumper and disconnect the electric socket.
4. Unscrew nuts of fastening of a bumper. On models with DOHC engines of a nut of fastening of a bumper are available from under the car.
5. At existence remove special rivets which both parties of a bumper to a wheel arch fix.
6. Remove additional brackets of fastening of a bumper which are from a reverse side of a bumper.
7. From a forward part of a bumper take clamps for what squeeze out from them the central pin.
8. Move each party of a bumper to a back part of the car, then disconnect the bumper ends from back wings.
9. Being careful, remove a bumper from a back part of the car, thus do not tear electroconducting of a lamp of illumination of registration plate.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.