Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
- 18. Electric equipment
   18.2. General information
   18.3. Electric chains
   18.4. Detection of a faulty chain
   18.5. Safety locks and relay
   18.6. Ignition lock
   18.7. Switch of lighting and indexes of turns
   18.8. Switch стеклоомывателя / screen wiper
   18.9. Switches on the dashboard
   18.10. Switch of adjustment of provision of an external mirror
   18.11. Switch of an electric drive of the hatch
   18.12. The switch of illumination of the salon, established in a door rack
   18.13. Switch of illumination of a luggage compartment
   18.14. Stoplight switch.
   18.15. Switch of a control lamp of the hand brake
   18.16. Sensor of pressure of oil
   18.17. Lighter illumination
   18.18. Hours
   18.19. A forward seat with heating
   18.20. Combination of devices
   18.21. Elements of a combination of devices
   18.22. Elements of the board computer
   18.23. Monitoring system and management elements
   18.24. Sound signal
   18.25. Lamp of illumination of salon
   18.26. Replacement of bulbs of internal lighting
   18.27. Headlight
   18.28. Engine of the proof-reader of light of headlights
   18.29. Adjustment of light of headlights
   18.30. System of reduction of intensity of light of headlights
   18.31. Forward index of turns
   18.32. Lateral repeater of turns
   18.33. Forward fog light
   18.34. Back lamps
   18.35. Lamp of illumination of registration plate
   + 18.36. Replacement of bulbs of external lighting
   18.37. Replacement of brushes of a screen wiper
   18.38. Screen wiper levers
   18.39. Washer jets
   18.40. Engine and drafts of a screen wiper
   18.41. Engine of a screen wiper of a back door
   18.42. Engine of a screen wiper of a headlight
   18.43. Tank of a stekloomyvatel
   18.44. Pump of a stekloomyvatel
   18.45. Unidirectional valve of a washer of headlights
   18.46. Elements of window regulators with an electric drive
   18.47. Programming of a control system by window regulators
   18.48. Elements of the central blocking of doors
   18.49. Aerial
   18.50. An aerial mast with an electric drive
   18.51. Loudspeakers
   18.52. Radio tape recorder
   18.53. Electric motor of a drive of the hatch
   18.54. Cable of a drive of a speedometer
   18.55. Anticreeping alarm system
   18.56. Elements of the anticreeping alarm system
   18.57. Safety cushion
   18.58. A safety cushion from the driver
   18.59. A steering wheel with a safety cushion
   18.60. Contact block of a safety cushion
   18.61. A safety cushion from the passenger
   18.62. A safety cushion arm from the passenger
   18.63. Control unit safety cushions
   + 18.64. Electric circuits
+ 19. Check of malfunctions



18.21. Elements of a combination of devices

GENERAL INFORMATION

Remove a combination of devices.

CONTROL LAMPS AND LAMPS OF ILLUMINATION OF THE COMBINATION OF DEVICES

Removal

Bulb removal with the boss from a combination of devices

PERFORMANCE ORDER
1. From a reverse side of a combination of devices turn a cartridge of the corresponding lamp on an hour hand and take it from the printed-circuit board (see fig. Bulb removal with the boss from a combination of devices).
2. Lamps are built in in a cartridge, and replacement them it is necessary to make as the block.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

VOLTAGE STABILIZER

Removal

Voltage stabilizer arrangement on the printed-circuit board of a combination of devices

PERFORMANCE ORDER
1. From a reverse side of a combination of devices unscrew the screw and remove стабилиза tension Torahs from contacts of the printed-circuit board (see fig. A voltage stabilizer arrangement on the printed-circuit board of a combination of devices).

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

FUEL AND TEMPERATURE INDEXES - MODELS OF A LOW SERIES

Removal

Removal of a forward frame of a combination of devices

PERFORMANCE ORDER
1. From the forward party of a combination of devices remove the button of zeroing of the daily counter.
2. In the top part of a combination of devices release two clamps and remove a forward frame of a combination of devices (see fig. Removal of a forward frame of a combination of devices).
3. Unscrew two nuts and take the corresponding index from a combination of devices.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

FUEL AND TEMPERATURE INDEXES - MODELS OF A HIGH SERIES

Removal and installation of indexes of fuel and temperature is made in the same way, as well as on models of a low series except that indexes fasten four nuts.

TACHOMETER

Arrangement of nuts of fastening of a tachometer

Removal and installation of a tachometer is made in the same way, as well as fuel and temperature indexes except that the tachometer fastens three nuts (see fig. Arrangement of nuts of fastening of a tachometer).

SPEEDOMETER

Removal

Arrangement of screws of fastening of a speedometer

PERFORMANCE ORDER
1. From the forward party of a combination of devices remove the button of zeroing of the daily counter.
2. In the top part of a combination of devices release two clamps and remove a forward frame of a combination of devices.
3. From the back party of a combination of devices unscrew four screws and remove a speedometer (see fig. Arrangement of screws of fastening of a speedometer).

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

PRINTED-CIRCUIT BOARD

Removal

PERFORMANCE ORDER
1. Remove from a combination of devices all lamps, indexes and a voltage stabilizer.
2. Being careful, remove the printed-circuit board from a combination of devices.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.