Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
- 18. Electric equipment
   18.2. General information
   18.3. Electric chains
   18.4. Detection of a faulty chain
   18.5. Safety locks and relay
   18.6. Ignition lock
   18.7. Switch of lighting and indexes of turns
   18.8. Switch стеклоомывателя / screen wiper
   18.9. Switches on the dashboard
   18.10. Switch of adjustment of provision of an external mirror
   18.11. Switch of an electric drive of the hatch
   18.12. The switch of illumination of the salon, established in a door rack
   18.13. Switch of illumination of a luggage compartment
   18.14. Stoplight switch.
   18.15. Switch of a control lamp of the hand brake
   18.16. Sensor of pressure of oil
   18.17. Lighter illumination
   18.18. Hours
   18.19. A forward seat with heating
   18.20. Combination of devices
   18.21. Elements of a combination of devices
   18.22. Elements of the board computer
   18.23. Monitoring system and management elements
   18.24. Sound signal
   18.25. Lamp of illumination of salon
   18.26. Replacement of bulbs of internal lighting
   18.27. Headlight
   18.28. Engine of the proof-reader of light of headlights
   18.29. Adjustment of light of headlights
   18.30. System of reduction of intensity of light of headlights
   18.31. Forward index of turns
   18.32. Lateral repeater of turns
   18.33. Forward fog light
   18.34. Back lamps
   18.35. Lamp of illumination of registration plate
   + 18.36. Replacement of bulbs of external lighting
   18.37. Replacement of brushes of a screen wiper
   18.38. Screen wiper levers
   18.39. Washer jets
   18.40. Engine and drafts of a screen wiper
   18.41. Engine of a screen wiper of a back door
   18.42. Engine of a screen wiper of a headlight
   18.43. Tank of a stekloomyvatel
   18.44. Pump of a stekloomyvatel
   18.45. Unidirectional valve of a washer of headlights
   18.46. Elements of window regulators with an electric drive
   18.47. Programming of a control system by window regulators
   18.48. Elements of the central blocking of doors
   18.49. Aerial
   18.50. An aerial mast with an electric drive
   18.51. Loudspeakers
   18.52. Radio tape recorder
   18.53. Electric motor of a drive of the hatch
   18.54. Cable of a drive of a speedometer
   18.55. Anticreeping alarm system
   18.56. Elements of the anticreeping alarm system
   18.57. Safety cushion
   18.58. A safety cushion from the driver
   18.59. A steering wheel with a safety cushion
   18.60. Contact block of a safety cushion
   18.61. A safety cushion from the passenger
   18.62. A safety cushion arm from the passenger
   18.63. Control unit safety cushions
   + 18.64. Electric circuits
+ 19. Check of malfunctions



18.26. Replacement of bulbs of internal lighting

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.

THE LAMP JOINING AT OPENING OF THE DOOR

Removal

PERFORMANCE ORDER
1. Using an edge of a thin screw-driver as the lever, take a lamp from a nest and disconnect from it the electric socket.
2. On models where the lamp joining at opening of a door is combined with a lamp for reading, for access to lamps remove a plafond.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

LAMP OF ILLUMINATION OF THE WARE BOX

Removal

PERFORMANCE ORDER
1. Using a screw-driver edge as the lever, remove a lamp from a nest and disconnect from it the electric socket.
2. Remove a bulb from a lamp.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

LAMP OF ILLUMINATION OF THE LUGGAGE COMPARTMENT, MOTOR COMPARTMENT AND CURB

Removal

Removal of a bulb from a lamp of illumination of a motor compartment

PERFORMANCE ORDER
1. Using an edge of a thin screw-driver as the lever, take a lamp from a nest and disconnect from it the electric socket.
2. Being careful, take a bulb from spring contacts of a lamp (see fig. Removal of a bulb from a lamp of illumination of a motor compartment).

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

LAMP OF ILLUMINATION OF THE LIGHTER

Removal

PERFORMANCE ORDER
1. Remove from the dashboard the block of the ashtray/lighter and disconnect the electric socket from a lamp of illumination of the lighter.
2. Having pulled, take a lamp from the boss.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

LAMP OF ILLUMINATION OF HOURS

Removal

Removal of the boss with a bulb of illumination of hours

PERFORMANCE ORDER
1. Remove hours.
2. Turn a cartridge with a bulb and remove it from a back part of hours (see fig. Removal of the boss with a bulb of illumination of hours).
3. Having pulled, take a lamp from the boss.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

LAMP OF ILLUMINATION OF THE DISPLAY OF THE BOARD COMPUTER

See the corresponding description above.

LAMP OF ILLUMINATION OF THE CONTROL PANEL HEATER

Removal

Removal of the boss with a bulb of illumination of the control panel a heater

PERFORMANCE ORDER
1. Remove the control panel a heater.
2. From a reverse side of the dashboard, having pulled, take a cartridge with a bulb (see fig. Removal of the boss with a bulb of illumination of the control panel a heater).
3. Having pulled, take a lamp from the boss.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.

LAMP OF ILLUMINATION OF THE MIRROR IN THE SUN-PROTECTION PEAK

Removal

PERFORMANCE ORDER
1. Lower a sun-protection peak and using an edge of a thin screw-driver as the lever, remove knot of a rasseivatel from a mirror. Take an illumination lamp from spring contacts.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.