Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
- 18. Electric equipment
   18.2. General information
   18.3. Electric chains
   18.4. Detection of a faulty chain
   18.5. Safety locks and relay
   18.6. Ignition lock
   18.7. Switch of lighting and indexes of turns
   18.8. Switch стеклоомывателя / screen wiper
   18.9. Switches on the dashboard
   18.10. Switch of adjustment of provision of an external mirror
   18.11. Switch of an electric drive of the hatch
   18.12. The switch of illumination of the salon, established in a door rack
   18.13. Switch of illumination of a luggage compartment
   18.14. Stoplight switch.
   18.15. Switch of a control lamp of the hand brake
   18.16. Sensor of pressure of oil
   18.17. Lighter illumination
   18.18. Hours
   18.19. A forward seat with heating
   18.20. Combination of devices
   18.21. Elements of a combination of devices
   18.22. Elements of the board computer
   18.23. Monitoring system and management elements
   18.24. Sound signal
   18.25. Lamp of illumination of salon
   18.26. Replacement of bulbs of internal lighting
   18.27. Headlight
   18.28. Engine of the proof-reader of light of headlights
   18.29. Adjustment of light of headlights
   18.30. System of reduction of intensity of light of headlights
   18.31. Forward index of turns
   18.32. Lateral repeater of turns
   18.33. Forward fog light
   18.34. Back lamps
   18.35. Lamp of illumination of registration plate
   + 18.36. Replacement of bulbs of external lighting
   18.37. Replacement of brushes of a screen wiper
   18.38. Screen wiper levers
   18.39. Washer jets
   18.40. Engine and drafts of a screen wiper
   18.41. Engine of a screen wiper of a back door
   18.42. Engine of a screen wiper of a headlight
   18.43. Tank of a stekloomyvatel
   18.44. Pump of a stekloomyvatel
   18.45. Unidirectional valve of a washer of headlights
   18.46. Elements of window regulators with an electric drive
   18.47. Programming of a control system by window regulators
   18.48. Elements of the central blocking of doors
   18.49. Aerial
   18.50. An aerial mast with an electric drive
   18.51. Loudspeakers
   18.52. Radio tape recorder
   18.53. Electric motor of a drive of the hatch
   18.54. Cable of a drive of a speedometer
   18.55. Anticreeping alarm system
   18.56. Elements of the anticreeping alarm system
   18.57. Safety cushion
   18.58. A safety cushion from the driver
   18.59. A steering wheel with a safety cushion
   18.60. Contact block of a safety cushion
   18.61. A safety cushion from the passenger
   18.62. A safety cushion arm from the passenger
   18.63. Control unit safety cushions
   + 18.64. Electric circuits
+ 19. Check of malfunctions



18.5. Safety locks and relay

GENERAL INFORMATION

Fuses

Arrangement of safety locks and the relay on the dashboard on SRi model of 2,0 l

Fuse removal on models of 2,0 l

Fuses are intended to break off a chain when the current in a chain exceeds admissible value.

Fuses are placed in the block of safety locks and the relay located under a cover from the bottom right side of the dashboard (see fig. An arrangement of safety locks and the relay on the dashboard on SRi model of 2,0 l). The arrangement of safety locks and the electric chains protected by safety locks, are given in inside on a cover of the block of safety locks and the relay.

Before removal of a safety lock switch off ignition. To remove a safety lock, simply take it from the socket (see fig. Fuse removal on models of 2,0 l). The wire in a safety lock is easily appreciable and will be broken off, if the safety lock fused.

Always replace a safety lock with other safety lock of the same capacity. Each safety lock has an inscription about size of a protected current. Never replace a safety lock more than once, without having defined the reason of its peregoraniye.

Relay

Arrangement of the block of the relay in a motor compartment on SRi model of 2,0 l

The relay is an electronic operated switch which is usually used as follows:

– the relay can switch big currents distantly from a chain in which this current flows, allowing to use thinner wires and contacts of switches;
– the relay can have more than one managing director of an entrance, unlike механичес whom the switch;
– the relay can carry out timer function, for example, to set an interval of work of screen wipers.

If the system operated by the relay, fails also a cause of defect, probably, the relay is, listen to operation of the relay at the included system. If the relay regularly works, you should hear click at its inclusion. If the relay is serviceable, the cause of defect is concluded in elements or connecting wires. If the relay does not work, it means that it does not receive the main power supply either an operating impulse, or the relay is faulty.

For replacement of the relay switch off ignition and, having simply pulled the relay, take it from a nest and insert on its place new.

The most part of the relay is located from a reverse side of the main block of safety locks. For access to the relay unscrew screws and take the block of safety locks, moving it forward. The relay of a back screen wiper is located in a back door behind the upholstery panel.

On some models additional relays are located in the block of the relay established on the left side of a motor compartment (see fig. An arrangement of the block of the relay in a motor compartment on SRi model of 2,0 l).