Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   + 2.9. Removal and engine installation together with a transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



2.10. Replacement of support of the engine and transmission

GENERAL INFORMATION

Prevention

At installation it is necessary to use new bolts of fastening of the left and right arm to a body.


The power unit fastens in a motor compartment on three support two of which are fixed on a transmission and one on the engine.

Arrangement of bolts of fastening of the right support of the power unit

1–fastening bolts to a body;

2–fastening bolts to the block of cylinders


Arrangement of bolts of fastening of the left support of the power unit

1–fastening bolts to a body;

2–bolts of fastening of an arm to the block

Right support

PERFORMANCE ORDER
1. Tighten the hand brake, then lift a forward part of the car and establish on supports.
2. Hook on the engine captures грузоподъ the emny mechanism and raise so that the weight of the engine was perceived by the load-lifting mechanism.
3. Working under the car, unscrew bolts of fastening of a support from the block of cylinders and a body. Take the right support of the power unit from under the car (see fig. Arrangement of bolts of fastening of the right support of the power unit).
4. Unscrew the fastening block from an arm.
5. Establish the new block of fastening on an arm and fix bolts, having tightened them the demanded moment.
6. Establish the right support of the power unit on the block of cylinders and fix bolts, having tightened them the demanded moment.
7. Fix the right support of the power unit to a body new bolts, having tightened them the demanded moment.
8. Disconnect captures of the load-lifting mechanism from the engine.
9. Lower the car on the earth.

Left support

PERFORMANCE ORDER
1. Tighten the hand brake, then lift a forward part of the car and establish on supports.
2. Hook on the engine captures грузоподъ the emny mechanism and raise so, that engine weight восприни мался the load-lifting mechanism.
3. Working under the car, unscrew the fastening block from an arm and a body (see fig. Arrangement of bolts of fastening of the left support of the power unit).
4. Using tap М10х1,25, clear a carving in body openings for fastening of the left support of the power unit.
5. Establish the new block of fastening on an arm and fix bolts, having tightened them the demanded moment.
6. Fix the left support of the power unit to a body and tighten bolts the demanded moment.
7. Disconnect captures of the load-lifting mechanism from the engine.
8. Lower the car on the earth.

Back support

PERFORMANCE ORDER
1. Tighten the hand brake, then lift a forward part of the car and establish on supports.
2. Hook on the engine captures грузоподъ the emny mechanism and raise so, that engine weight восприни мался the load-lifting mechanism.
3. Working under the car, unscrew a back support from the bottom frame and an arm.
4. Establish the new block of fastening on the bottom frame and an arm and fix bolts, having tightened them the demanded moment.
5. Disconnect captures of the load-lifting mechanism from the engine.
6. Lower the car on the earth.