Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   + 2.9. Removal and engine installation together with a transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6

GENERAL INFORMATION

On models 1991 and 1992 of year with l engines 1,4 and 1,6 in a back casing of a gear belt there is a small opening over a casing of the oil pump. Through this opening penetration of extraneous subjects (gravel) that can serve as the reason of a pereskakivaniye of a gear driving belt on teeths of pulleys is possible. On this opening of steel устанав ливать on models since 1993, and on earlier models the opening independently is desirable to close a stopper.

There is a special rubber stopper No. 90469594 for opening closing. On models without the amplifier of a steering the stopper can be inserted into an opening from above. On models with the amplifier of a steering it is possible to establish a stopper in an opening from below. For improvement of access to an opening, at stopper installation, it is desirable to remove a ridge driving belt.