Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   + 2.9. Removal and engine installation together with a transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



2.27. Oil pallet

GENERAL INFORMATION

Prevention

At installation of the oil pallet it is necessary to use new laying and hermetic at installation of the oil pump and the back radical bearing.


Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Merge from the engine engine oil, then establish into place a masloslivny stopper and tighten it the demanded moment.
3. Tighten the hand brake, then lift a forward part of the car and fix on supports.
4. Remove a reception exhaust pipe.
5. At existence disconnect the electric socket from the sensor of level of the engine oil established in the oil pallet.
6. Unscrew bolts and remove a protective plate of coupling.
7. Evenly and gradually unscrew bolts of fastening and remove the oil pallet. Keep in mind that on the majority of models the reflector of oil of the oil pallet can be moved on considerable distance from the block of cylinders together with the oil pallet, but it cannot be removed until the maslozaborny tube of the oil pump will be removed.
8. On l models 1,6, 1,8 and 2,0 for removal of a reflector of oil it is necessary to unscrew an arm, fixing a maslozaborny tube of the oil pump to the block of cylinders. The reflector of oil can be removed through a maslozaborny tube. On the l NZ2 1,8 and 2,0 C16 models with an oil reflector a screw-driver remove rubber laying.
9. For removal of a maslozaborny tube of the oil pump unscrew a bolt, a fixing arm to the block of cylinders and two bolts, fixing the end of a maslozaborny tube to the oil pump. Remove condense a telny ring of round section.
10. Clear interfaced surfaces of the block of cylinders, a reflector of oil and the oil pallet of traces of old laying and hermetic.

Installation

Places of drawing of hermetic on interfaced surfaces of the oil pump and a back cover of the radical bearing

Drawing of a layer of hermetic on an interfaced surface of the oil pump and the block of cylinders of the engine on the engine of 2,0 l

Installation of new rubber laying on an oil reflector on the engine of 2,0 l

Installation of a new sealing ring of round section on a maslozaborny tube

Tightening of bolts of fastening of a maslozaborny tube on the engine of 2,0 l

Installation of an arm of fastening of a maslozaborny tube on the engine of 2,0 l

Drawing on a carving of bolts of fastening of the oil pallet of the means interfering their unscrewing

Installation of the oil pallet on the engine of 2,0 l

PERFORMANCE ORDER
1. Apply a thin film Opel No. 90485251 hermetic on interfaced surfaces between the oil pump and the block of cylinders and between a back cover of the radical bearing and the block of cylinders (see fig. Places of drawing of hermetic on interfaced surfaces of the oil pump and a back cover of the radical bearing, layer Drawing гермети on an interfaced surface of the oil pump and the block of cylinders of the engine on the engine of 2,0 l).
2. On the NZ2 1,8 and 2,0 C16 models of l establish new rubber laying on perimeter of a reflector of oil (see fig. Installation of new rubber laying on an oil reflector on the engine of 2,0 l).
3. On models 1,6, 1,8 and 2,0 of l establish an oil reflector in the block of cylinders, moving it through an intaking tube of the oil pump.
4. If the maslozaborny tube acted in film, establish it on the oil pump with a new sealing ring of round section and fix bolts, having tightened them the demanded moment (see fig. Installation of a new sealing ring of round section on a maslozaborny tube, the Tightening of bolts of fastening of a maslozaborny tube on the engine of 2,0 l).
5. At existence, establish an arm of fastening of a maslozaborny tube to the block of cylinders (see fig. Installation of an arm of fastening of a maslozaborny tube on the engine of 2,0 l).
6. Put on a carving of bolts of fastening of the oil pallet means, to a prepyatstvo yushchy to their unscrewing (Opel No. 90167347), then establish the oil pallet and fix bolts, having tightened them the demanded moment (see fig. Drawing on a carving of bolts of fastening of the oil pallet of the means interfering their unscrewing, Installation of the oil pallet on the engine of 2,0 l).
7. If the engine is established in автомоби to le, further installation is made in sequence, return to removal. Fill in in the engine engine oil.