Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   + 2.9. Removal and engine installation together with a transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



2.28. Oil pump

Removal

PERFORMANCE ORDER
1. Remove a gear belt, pulleys and a back casing of a gear belt.
2. Remove the oil pallet, a maslozaborny tube of the oil pump and an oil reflector.
3. On NZ2 1,8 and 2,0 C16 engines of l unscrew the oil filter from fastening on the oil pump.
4. Disconnect the electric socket from the sensor of pressure of the oil established on the oil pump.
5. Unscrew bolts and take the oil pump from the block of cylinders. Remove laying of the oil pump.

Installation

Installation of new laying of the oil pump on the block of cylinders of the engine of 2,0 l

Arrangement of a shestigrannik on cranked to a shaft for a drive of an internal rotor of the oil pump on l engines 1,4 and 1,6

Arrangement лысок on cranked to a shaft for a drive of an internal rotor of the oil pump on l engines 1,8 and 2,0

Tightening of bolts of fastening of the oil pump on двигате le SOHC of 2 l

PERFORMANCE ORDER
1. Clear interfaced surfaces of the oil pump and the block of cylinders, then establish on the block of cylinders new laying of the oil pump (see fig. Installation of new laying of the oil pump on the block of cylinders of the engine of 2,0 l).
2. For protection of working edges condense a telny ring at installation of the oil pump wrap up a sticky tape a cranked shaft.
3. Establish the oil pump, thus an internal rotor of the pump should settle down correctly on шестигранни ке a cranked shaft. Screw in bolts of fastening of the oil pump and tighten them the demanded moment. Remove a sticky tape from a cranked shaft (see fig. An arrangement of a shestigrannik on cranked to a shaft for a drive of an internal rotor of the oil pump on l engines 1,4 and 1,6, the Arrangement лысок on cranked to a shaft for a drive внутрен it a rotor of the oil pump on l engines 1,8 and 2,0, the Tightening of bolts of fastening of the oil pump on двигате le SOHC of 2 l).
4. If the engine is established in the car, further installation is made in sequence, return to removal. Fill in in the engine engine oil.
5. Connect the electric socket to the sensor of pressure of oil.
6. On NZ2 1,8 and 2,0 C16 engines of l establish the new oil filter.
7. Establish an oil reflector, маслоза a boric pipe of the oil pump and the oil pallet.
8. Establish a back casing of a gear belt, a gear belt and adjust a tension of a gear belt.