Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
- 2. Engine
   2.2. General information
   2.3. System of ventilation of a case
   2.4. Compression check
   2.5. Repair operations on the engine established in the car
   2.6. The repair operations demanding removal of the engine
   2.7. Recommendations about engine removal
   + 2.8. Removal and engine installation without a transmission
   + 2.9. Removal and engine installation together with a transmission
   2.10. Replacement of support of the engine and transmission
   2.11. Engine repair
   + 2.12. A gear belt and pulleys (without the automatic mechanism of a tension)
   2.13. A gear belt and the tension mechanism (l models 1,4 and 1,6 except С16 NZ2)
   2.14. An opening in a back casing of a gear belt on l models 1,4 and 1,6
   2.15. Gear belt and tension mechanism (l NZ2 1,8 and 2,0 C16 model)
   2.16. Forward sealing ring of a camshaft
   2.17. Back sealing ring of a camshaft
   2.18. Camshaft and camshaft case
   + 2.19. Removal and installation of a head of the block of cylinders on the engine in the car
   2.20. Removal and installation of a head of the block of cylinders on the removed engine
   + 2.21. Repair of a head of the block of cylinders
   2.22. Cleaning and survey of a head of the block of cylinders
   2.23. Hydraulic pushers of valves
   2.24. Flywheel
   2.25. Replacement of a forward sealing ring of a cranked shaft
   2.26. Replacement of a back sealing ring of a cranked shaft
   2.27. Oil pallet
   2.28. Oil pump
   2.29. Repair of the oil pump
   2.30. Removal and installation of pistons and rods
   2.31. Check of pistons and rods
   + 2.32. Removal and installation of a cranked shaft
   2.33. Check of a cranked shaft
   2.34. Survey and gap check in radical and shatunny bearings
   2.35. Check of a working gap of the bearing
   2.36. Check of the block of cylinders of the engine
   2.37. Engine start after major maintenance
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



2.37. Engine start after major maintenance

PERFORMANCE ORDER
1. On the engine established in a motor compartment of the car, check levels of engine oil and cooling liquid. Check that all earlier removed wires and hoses are established on the places.
2. On cars with petrol engines disconnect the electric socket from the block of ignition and remove the relay of the fuel pump. Turn the engine a starter until the control lamp of pressure of oil will not go out, then connect электричес a cue the socket to the block of ignition and establish the relay of the fuel pump.
3. Start the engine. Start of the engine can be more long, than usually because of shutdown of fuel system.
4. At operation of the engine idling check existence of leakages of the fuel, cooling liquid and oil. At this stage of operation of the engine the smell and a smoke from warm parts of the engine can be observed at burning out of the oil which has got on the engine at assembly.
5. The engine should idle until cooling liquid will not heat up that will be felt through the top hose of a radiator. Then switch off the engine.
6. After cooling of the engine check level of oil and cooling liquid.
7. At installation in the engine of new pistons, piston rings or bearings of a cranked shaft it is necessary to make an engine running in during run of the first 800 km. Do not maintain the engine with completely open butterfly valve or under big loading at low frequency of rotation of the engine. It is recommended to replace oil and the oil filter at the end of the running in period.