Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
- 4. Repair of the diesel engine
   4.2. General information
   4.3. The repair which is not demanding removal of the engine
   4.4. Compression check
   4.5. Top dead point (VMT) of the piston of the first cylinder
   4.6. Cover of a head of the block of cylinders
   4.7. Pulley of a cranked shaft
   4.8. Casings of a gear belt
   4.9. Replacement of a gear belt
   4.10. Check and installation of phases of a gazoraspredeleniye
   + 4.11. Mechanism of a tension of a gear belt and pulleys
   4.12. Replacement of a sealing ring of a camshaft
   4.13. Check and adjustment of gaps of valves
   4.14. Camshaft and pushers
   4.15. Head of the block of cylinders
   4.16. Oil pallet
   4.17. Oil pump
   4.18. Replacement of a sealing ring of the oil pump
   4.19. Oil radiator
   + 4.20. Pistons with rods
   4.21. Flywheel
   4.22. Replacement of sealing rings of a cranked shaft
   4.23. Replacement of support of the power unit
   4.24. Recommendations about engine removal
   4.25. Removal and engine installation
   4.26. Engine repair
   4.27. Engine start after major maintenance
+ 5. Cooling system
+ 6. Fuel system
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



4.16. Oil pallet

GENERAL INFORMATION

Oil pallet

1–oil reflector;

2–top part of the pallet;

3–lower part of the pallet


Drawing of a thin layer of hermetic on the top part of the oil pallet

Removal

Removal of the lower part of the oil pallet

Removal of a maslopriyemny pipe

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Lift a forward part of the car and fix on supports.
3. Merge engine oil from the engine. Establish a new washer on a masloslivny stopper and screw up a stopper in the oil pallet.
4. Unscrew bolts and remove the lower part of the oil pallet (see fig. Removal of the lower part of the oil pallet).
5. To remove a body of the oil pallet, remove a forward exhaust pipe.
6. Unscrew bolts and remove the bottom protective plate of a flywheel.
7. Gradually unscrew bolts of fastening of a body of the oil pallet to a cover of the pump and the block of cylinders of the engine. Take a body of the oil pallet from under the car.
8. Unscrew bolts and remove a maslopriyemny pipe with the mesh filter (see fig. Removal of a maslopriyemny pipe).

Installation

Installation of a new sealing ring on a pipe of a maslopriyemnik

PERFORMANCE ORDER
1. Clear all traces of dirt and oil from interfaced surfaces of the oil pallet and the block of cylinders.
2. Establish a new sealing ring on a pipe of a maslopriyemnik and establish a pipe of a maslopriyemnik on the engine (see fig. Installation of a new sealing ring on a pipe of a maslopriyemnik).
3. Check that interfaced surfaces of the main block of the oil pallet and the block of cylinders pure and dry and apply a thin film hermetic on the top part of the main oil pallet.
4. Establish the main block of the oil pallet on the block of cylinders and fix bolts. A tightening of bolts make from the center in diagonal sequence.
5. Establish a protective plate of a flywheel.
6. Establish a forward exhaust pipe.
7. Check that interfaced surfaces of the oil pallet and the bottom oil pallet pure and dry. Apply a thin film hermetic on an interfaced surface of the bottom oil pallet. Establish the bottom oil pallet and fix bolts.
8. Lower the car and fill in in the engine engine oil.