Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
- 6. Fuel system
   6.2. General information
   6.3. Air filter
   6.4. The block of adjustment of temperature of air arriving in the engine
   6.5. Check of the fuel pump
   6.6. Removal and installation of the fuel pump
   6.7. Fuel tank
   6.8. Fuel level sensor
   6.9. Separator паров fuels (l model 1,6 and 1,8)
   6.10. Accelerator pedal
   6.11. Accelerator cable
   6.12. Carburetor
   6.13. Removal and carburetor installation
   6.14. Adjustment of turns of idling and the contents WITH
   6.15. Needle and float
   6.16. Vacuum diaphragm of a butterfly valve of the secondary chamber
   6.17. Diaphragm of an ekonomayzer
   6.18. Accelerating pump
   6.19. Knot of an air automatic zaslonka
   + 6.20. Vacuum blocks of moving of an air automatic zaslonka
   6.21. Carburetor filter
   6.22. Adjustment of the shock-absorber of a butterfly valve
   6.23. Sensor of provision of a butterfly valve (an automatic transmission)
   6.24. Check of the valve of increase in turns of idling
   6.25. The electromagnetic valve of idling on models of 1,8 l
   6.26. Inlet collector
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



6.11. Accelerator cable

Removal

Unscrewing of the screw of fastening of the air chamber

Removal of a bracket of fastening of a cover of a cable of an accelerator to an arm

Removal of a sealing ring of a cable of an accelerator from an arm

PERFORMANCE ORDER
1. On early models remove the air filter. On later models disconnect an air line from the air filter. Then disconnect a vacuum tube and a hose of ventilation of a case from the air chamber. Unscrew three screws and remove the air chamber together with an air line (see fig. Unscrewing of the screw of fastening of the air chamber).
2. Remove a bracket, a fixing cover of a cable of an accelerator to an arm on the carburetor, then remove a sealing ring from an arm (see fig. Removal of a bracket of fastening of a cover of a cable of an accelerator to an arm, Removal of a sealing ring of a cable of an accelerator from an arm).
3. Remove an accelerator cable from the butterfly valve lever on the carburetor.
4. In salon of the car remove the bottom panel of furnish in deepening for feet of the driver.
5. Remove a cover of a cable of an accelerator from an arm on the top part of a pedal and disconnect a cable from an accelerator pedal.
6. Take an accelerator cable in a motor compartment.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal taking into account the next moments.
2. Check correctness of an arrangement of a cable of an accelerator.
3. Check that the sealing ring of a cover of a cable of an accelerator is correctly established in an opening of a partition of a motor compartment.

Adjustment

Arrangement of the persistent screw of a pedal of an accelerator

PERFORMANCE ORDER
1. Believe work of a butterfly valve and, if necessary, adjust an accelerator cable.
2. Two adjustments of a cable of an accelerator are applied. The first is a persistent screw on the pedal lever, for adjustment of provision of completely released pedal of an accelerator (see fig. Arrangement of the persistent screw of a pedal of an accelerator). The second – a bracket fixing a cover of a cable of an accelerator in an arm on the carburetor, is intended for adjustment of sagging of a cable.
3. The cable of an accelerator should be adjusted so that at completely released pedal of an accelerator the cable of an accelerator had small sagging from the carburetor.
4. Check that at completely pressed pedal of an accelerator the butterfly valve completely opens. Adjustment of a cable of an accelerator is made by shift of the bracket, fixing a cover of a cable of an accelerator to an arm of the carburetor and the persistent screw of the limiter of a pedal of an accelerator.