Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
- 6. Fuel system
   6.2. General information
   6.3. Air filter
   6.4. The block of adjustment of temperature of air arriving in the engine
   6.5. Check of the fuel pump
   6.6. Removal and installation of the fuel pump
   6.7. Fuel tank
   6.8. Fuel level sensor
   6.9. Separator паров fuels (l model 1,6 and 1,8)
   6.10. Accelerator pedal
   6.11. Accelerator cable
   6.12. Carburetor
   6.13. Removal and carburetor installation
   6.14. Adjustment of turns of idling and the contents WITH
   6.15. Needle and float
   6.16. Vacuum diaphragm of a butterfly valve of the secondary chamber
   6.17. Diaphragm of an ekonomayzer
   6.18. Accelerating pump
   6.19. Knot of an air automatic zaslonka
   + 6.20. Vacuum blocks of moving of an air automatic zaslonka
   6.21. Carburetor filter
   6.22. Adjustment of the shock-absorber of a butterfly valve
   6.23. Sensor of provision of a butterfly valve (an automatic transmission)
   6.24. Check of the valve of increase in turns of idling
   6.25. The electromagnetic valve of idling on models of 1,8 l
   6.26. Inlet collector
+ 7. A fuel and exhaust system of models with system of injection of fuel
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



6.18. Accelerating pump

Check

Adjustment of productivity of the accelerating pump, "+" to increase ", -" to reduce

PERFORMANCE ORDER
1. At check of operability of the accelerating pump it is necessary to submit to the poplavkovy chamber fuel from the additional tank.
2. Establish the primary chamber of the carburetor over a volumetric glass. Ten times completely open and close a throttle a ny zaslonka, and opening of a zaslonka make within one second then return a zaslonka to a starting position and in three seconds repeatedly open it. Check, that the cam of the accelerated turns of idling did not limit butterfly valve moving.
3. Measure amount of fuel which the accelerating pump submitted to a volumetric glass, and compare these data with technically ми characteristics.
4. If adjustment is required, weaken the screw of fastening and turn a cam in the demanded direction then tighten the screw and repeatedly check productivity of the accelerating pump (see fig. Adjustment of productivity of the accelerating pump).

Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. On early models remove the air filter. On later models disconnect an air pipe from the air filter, then disconnect a vacuum pipe and a hose of ventilation of a case from the air chamber. Unscrew three screws and remove the air chamber together with an air line.
3. Clear an external surface of the accelerating pump.
4. Unscrew four screws and uncover the accelerating pump, a diaphragm, a spring, a support of a spring and the valve.

Installation

Elements of the accelerating pump

1–a cover with a control lever;
2–diaphragm;
3–spring;
4–valve;
5–an opening for air


PERFORMANCE ORDER
1. Clear interfaced surfaces of a cover of the accelerating pump and the carburetor case.
2. Check a condition of the valve of the accelerating pump and, if necessary, replace it.
3. Establish the valve, a support of a spring and a spring in the carburetor case. In big diameter the spring should be направле on to the carburetor.
4. Establish in the carburetor case a diaphragm and a cover of the accelerating pump. Gradually and evenly screw up screws of fastening of a cover of the accelerating pump not to deform a diaphragm (see fig. Elements of the accelerating pump).
5. Further installation is made in sequence, return to removal.