Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. A fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit in temperature of air arriving in the engine
   7.7. The sensor of temperature of air arriving in the engine
   7.8. Pressure removal in fuel system
   7.9. The fuel filter on models with the fuel pump out of a fuel tank
   7.10. The fuel filter on models with the pump in a fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump established out of a fuel tank
   7.13. The fuel pump established in a fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a toplivozalivny mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of a fuel mix on idling turns
   7.21. Regulator of pressure of fuel
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Measuring instrument of a stream of air
   7.26. Measuring instrument of weight of a stream of air
   7.27. Tape measuring instrument of weight of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step-by-step engine of management of supply of air (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor detonations (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



7.25. Measuring instrument of a stream of air

GENERAL INFORMATION

Prevention

At installation of a bell of an air inlet establish new laying. Before a vvinchivaniye of bolts of fastening of a measuring instrument of a stream of air put on a carving of bolts the means interfering their unscrewing.


Removal

Arrangement of a bolt of fastening of a measuring instrument of a stream of air on the SOHC models

Arrangement of bolts of fastening of a measuring instrument of a stream of air

PERFORMANCE ORDER
1. Remove the air filter.
2. Unscrew a bolt, a fixing measuring instrument of a stream of air to a cover of the air filter (see fig. An arrangement of a bolt of fastening of a measuring instrument of a stream of air on the SOHC models).
3. From the interior of a cover of the air filter unscrew four bolts and remove two strengthening plates, then remove a measuring instrument of a stream of air (see fig. Arrangement of bolts of fastening of a measuring instrument of a stream of air).
4. If necessary remove an air bell from the interior of a cover of the air filter.

Installation

Installation is made in sequence, return to removal taking into account the next moments...

PERFORMANCE ORDER
1. At installation of an air bell use new laying.
2. Put on a carving of four bolts of fastening of a measuring instrument of a stream of air the means interfering unscrewing of bolts.