Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. A fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit in temperature of air arriving in the engine
   7.7. The sensor of temperature of air arriving in the engine
   7.8. Pressure removal in fuel system
   7.9. The fuel filter on models with the fuel pump out of a fuel tank
   7.10. The fuel filter on models with the pump in a fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump established out of a fuel tank
   7.13. The fuel pump established in a fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a toplivozalivny mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of a fuel mix on idling turns
   7.21. Regulator of pressure of fuel
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Measuring instrument of a stream of air
   7.26. Measuring instrument of weight of a stream of air
   7.27. Tape measuring instrument of weight of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step-by-step engine of management of supply of air (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor detonations (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



7.27. Tape measuring instrument of weight of a stream of air

Removal

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Disconnect electric sockets from a tape measuring instrument of weight of a stream of air and the sensor of temperature of air arriving in the engine.
3. Remove the top part of the air filter together with an air inlet and a measuring instrument of weight of a stream of air.
4. Weaken collars and remove a measuring instrument of weight of a stream of air with воздухозаборни, thus note the provision of a measuring instrument of weight of a stream of air. In the presence of damages replace the block.

Installation

Connection of a tape measuring instrument of weight of a stream of air – Motronic M2.8

1–electric socket of a tape measuring instrument of weight of a stream of air;

2–the electric socket of the sensor of temperature of air arriving in the engine


Connection of an air inlet with a tape measuring instrument of weight of a stream of air Motronic M2.8
Shooters showed grooves of combination of a vozdukhokhabornik with a measuring instrument of a stream of air.

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal. Check correctness of a relative positioning of the main air branch pipe and a measuring instrument of a stream of air (see fig. Connection of a tape measuring instrument of weight of a stream of air – Motronic M2.8, Connection of an air inlet with a tape measuring instrument of weight of a stream of air – Motronic M2.8). Also check combination of labels on an air inlet and the air chamber.