Opel Vectra A

since 1988-1995 of release

Repair and car operation



Vektr A. Opel
+ 1. Maintenance instruction
+ 1.1 Maintenance
+ 2. Engine
+ 3. Repair of DOHC engines
+ 4. Repair of the diesel engine
+ 5. Cooling system
+ 6. Fuel system
- 7. A fuel and exhaust system of models with system of injection of fuel
   7.2. General information
   7.3. Check of system of injection of fuel
   7.4. Air filter
   7.5. Air chamber
   7.6. The control unit in temperature of air arriving in the engine
   7.7. The sensor of temperature of air arriving in the engine
   7.8. Pressure removal in fuel system
   7.9. The fuel filter on models with the fuel pump out of a fuel tank
   7.10. The fuel filter on models with the pump in a fuel tank
   7.11. Check of the fuel pump
   7.12. The fuel pump established out of a fuel tank
   7.13. The fuel pump established in a fuel tank
   7.14. Replacement of the relay of the fuel pump
   7.15. Pipe of a toplivozalivny mouth
   7.16. Fuel tank
   7.17. Fuel level sensor
   7.18. Quencher of fluctuations of fuel
   7.19. Accelerator cable
   7.20. Check and adjustment of a fuel mix on idling turns
   7.21. Regulator of pressure of fuel
   7.22. Regulator of turns of idling
   7.23. Sensor of provision of a butterfly valve
   7.24. Potentiometer of provision of a butterfly valve
   7.25. Measuring instrument of a stream of air
   7.26. Measuring instrument of weight of a stream of air
   7.27. Tape measuring instrument of weight of a stream of air
   + 7.28. Fuel nozzles (except Multec)
   7.29. Fuel nozzle (Multec system)
   7.30. Check of a fuel nozzle (Multec system)
   + 7.31. The throttle case (except Multec system)
   7.32. Throttle case (Multec system)
   7.33. Step-by-step engine of management of supply of air (idling turns)
   7.34. Potentiometer of provision of a butterfly valve
   7.35. Electronic control device (ECU)
   7.36. Sensor of a detonation and module (X16 SZ models)
   7.37. Sensor detonations (Simtec system)
   7.38. An inlet collector (the SOHC engine without Multec)
   7.39. An inlet collector (the SOHC engine with Multec)
   7.40. Inlet collector (DOHC models)
+ 8. Exhaust system and system of fall of toxicity of exhaust gases
+ 9. Fuel systems of the diesel engine
+ 10. Engine electrosystems
+ 11. Transmission
+ 12. Mechanical transmission
+ 13. Automatic transmission
+ 14. Power shafts
+ 15. Brake system
+ 16. Suspension bracket
+ 17. Body
+ 18. Electric equipment
+ 19. Check of malfunctions



7.5. Air chamber

Removal

Connection of vacuum pipes to the air chamber

And – to the throttle case;

In – to air the filter


PERFORMANCE ORDER
1. The air chamber fastens two or three bolts to the top part of the case of a throttle. Mark vacuum tubes of system of adjustment of temperature of air arriving in the engine.
2. Disconnect a hose of ventilation of a case of the engine from the air chamber and a vacuum pipe from a back part of the case of a throttle (see fig. Connection of vacuum pipes to the air chamber).
3. At removal of the air chamber keep a sealing ring.

Installation

Arrangement of a sealing ring in a flute of the air chamber

Tightening of bolts of fastening of the air chamber
Tightening of bolts of fastening of the air chamber make with moderate effort.

PERFORMANCE ORDER
1. At installation check correctness of installation of a sealing ring in a groove from a reverse side of the air chamber. Fix the air chamber bolts and connect a vacuum pipe and a hose of ventilation of a case (see fig. An arrangement of a sealing ring in a flute of the air chamber, the Tightening of bolts of fastening of the air chamber).